PDA

View Full Version : Fast boys camaro set up



Master X
05-08-2012, 03:03 PM
Hey guys I've been reading up on the fast boys set up and want to try it on my camaro. I have a few questions though. Its a street stock class and everything has to be stock mounting including the shocks. So is it vital to float the rr? Do they make a stock appearing one? Will it want to wheel hop with shocks in stock position? Also what exact rate should I start with for the spring on lr?

All help is appreciated!

DaveBauerSS6
05-12-2012, 01:19 AM
Haven't ran that setup with stock location and stock shocks. Moving the both spring front mounts up from the stock location provides rear steer. The floater needs rear steer to help turn . Not sure if you could tune around that. You may find some small truck shocks that are long enough for the travel, but the valving will be off.
I built my own floater when it was illegal and got figured out when the left front wheel was a foot off the ground.
Running that setup in a mod, there is room on the rules to make it work. Stock type chassis gets complicated and the tuning is almost backwards to a conventional setup. You will need a lot of devotion to get it to win. If you do it get another car and work together. Time is your enemy.

Good luck...........

Dirtrunner35
05-13-2012, 07:29 PM
If the RR is not floated it's not a fast boy

outlawstreet21
05-13-2012, 09:38 PM
Will it work? Yes. I have run this setup for the past three years. If you are on a tacky hooked up track I would lock the floater anyways on a camaro. Now if your running on a dry slick track and not using a floater for this setup, welllll your wasting your time. I run my shocks in the stock location due to our rules. When the track goes slick I sometimes even take the left rear shock off. This lets the left rear travel further not being connected. Never have had any wheel hop from this, but I broke the right rear shock once and it about shook the car to pieces.

Your spring rates will be determined by what your car weighs. For example a 3000-3200lbs. I would start with a 200 lr and 175 rr with landrums or Afco 205 lr and 176 rr. If using the Afcos I would get the reinforced front segment for the lr.

Master X
05-14-2012, 03:15 PM
Do u guys suggest that I just run the afco reinforced spring then? Or should I make a floater and do the lr spring trick? This will be around 3000 pounds.

Dirtrunner35
05-14-2012, 05:13 PM
I ran the stock springs on mine with it floated with no problems. If your allowed shackles make sure the left rear has more angle in it then stock, this will help let the axle down more on that side for more bite .

racing9HVR
05-15-2012, 06:11 AM
sorry to hi-jack this thread, but we do you find this set up? I have searched the web and just keep finding people asking about the setup. Thanks and sorry once again

outlawstreet21
05-15-2012, 04:20 PM
Post from another thread.

FASTBOYS leaf tech(get it here)
Let's try this one more time
I am not too good at this typing and spelling thing, but I think you can get what you need to know about this setup
from this thread
I will start with a good base setup for what we will call the Fast Boys leaf setup.
Forget everything you ever knew about leaf springs (also most of what you do on bar cars is backwards from the way this deal works)When a bar car gets up on the bars the l/r tire walks forward, making the car loose. With this setup when the car hikes up on the l/r and the pinion rotates up the l/r tire goes back (making the car tighter).
Let's start with taking a standard stacked leaf car and making it into a fast boy's rear.
There are two ways to do this, the first is the easiest and would be a good way to start (easier to drive until you get
the feel for how tight it will be to drive).Leave the r/r leaf the way it comes(can use a 150 or 175 Ibs stacked leaf), instead of clamping it to the rear-end with u bolts you need to float the r/r spring mount on a bird cage. Leave the r/r shackels alone .Make sure you mount the r/r shock off of the rear end tube (instead of the lower spring plate) or it will wheel hoop.
Rebuilding the L/R leaf
Next you need to redo the l/r leaf spring and mounts on that side. This is the same for both the mono and stacked
setup, and the 2 stacked leafs setup we are talking about now.
1 have mostly used afco leafs in the past but I do like the new landrums that I have been working with now. I take
an afco 31 and rebuild it to make it hook on slick tracks. Take and cut the bands off and move the 2nd leaf down
(the one next to the main ) and redrill the center hole 3"s back ( moving the front of it forward). Now take the 3rd
leaf and turn it around 180 (front to back) and use the same hole. Now take the 4th small leaf and throw it away.
While you have it apart you will see that the main leaf doesn't have enough arche in it. I like to rearch it so that
when it is standing on the floor with the eyes down it is about 7 or 8"s tall at the center pin. Only put the arch in the
front of the spring (from the eye forward).also I like to add some arch from the pin forward in the other 2 leafs also.
When you bolt it back together only band the front of the spring (not the back).
What this has done is made the front of the spring stronger to deal with the increased load that this setup has on it, but the spring rate is now softer (letting it flatten out at ride height) and the extra arch will still want to come back into it when the l/r is hiked up (keeping the l/r tire on the ground and digging).It is important that you DON'T try to run the standard alum lowering block and u bolts on this deal (they will break). I run a 2" block on the r/r and a steel hand made bracket on the l/r that would be like running a 3" block. If you buy the parts from R C for this it is important that you weld the l/r bracket all the way around the rear end (the l/r is the only thing doing the lifting and it will try to tear everything over there off).
L/R Shackle
Now for the l/r shackle. This is where you will tune for heavy or dry tracks. You need to be able to put the top mount forward so that when at ride height the shackle has about 40 degrees of angle in it .I put my mounts on top of the frame rail and run a long 11" set of shackles. If you hook a tape in the 5/8 ths hole that the front spring eye goes in and measure back to the top of the rear frame rail make a mark at 51 "s and 53.5"s this is where the top shackle bushings need to weld on. Run the front hole for dry tracks and the back hole for heavy tracks when you want to take the wheelie out.
Shocks
As for shocks on this deal, softer is better. I run 93 on r/r 94 on l/r and a pair of 74 s on the front. You don't run any 90/10 wrap-up shocks or any pull bars or 5th arms on here (been there tried that didn't work as good.) Make sure you mount the l/r shock so that it has about 6"s to come out and only 3 in when at ride height. Also keeping the back of the car lower is faster with this setup.
Mono - coil R/R setup
This is the full blown (Full Tilt) way to do this deal. It takes a bit to get used to driving ,and is not for everyone The
car will be tight when you pick the gas back up, and also have more side bite going in. You can drive the car way
into the turn and when the tail comes out and most cars would have to wait to get back on it till the tail is back
under you, instead you pick the gas up while the tail is out and it will bring the tail back under you. This is because
of two things, first the l/r spring is the only thing that is putting load in the rear end when you pick up the gas, so it
gains a bunch of l/r bite when you are on the gas (probably gains around 200 to 300 Ibs or so) but when your off
the gas and on the brakes going in it gains r/r giving you more side bite.
The other thing that this does is the roll steer. Bar cars move the r/r back and the L/R forward when they get on the
gas. This makes the car loose and so they have to run more wedge to keep the car straight coming off the turn,
that makes the car loose going in and loose through the center.
With this set-up when you're on the gas the L/R tire goes back in the wheel well and tightens up the car. The mono
on the r/r is all that is pushing the car forward on that side and is floated so the wrap-up is out of the picture. This
makes the mono s up some and moves the r/r tire forward in the wheel well. This roll steer along with the way the
r/r coil is mounted makes the car tight when you're on the gas and tight when you're on the brakes.
Here's how to do the r/r.
Put a mono on the r/r (I use the main leaf out of an old stacked leaf).You have to float it on a bird cage just like our
2 stacked deal was. Here is where you have to get this correct at. Mounting the coil on the r/r.You have to mount it
on the back side of the rear end tube and to the tube itself (not the bird cage or the lower plate).try to get it about
7"s from the center line of the axle (much like a coil over mount on a l/m clamp bracket would look).Try to get the
top of the coil in about 15 degrees and also back 15 degrees.
I run a 125 coil spring over there, but most guys like to start with around 150 .Mount the shock off the front of the
tube and go in and forward on the top mounts.
R C race cars sells all of these mounts if you can't build them.
Set-up
Here are some basic numbers for my type leaf car. Each car is a bit different, but try to keep the rear and left side
percentages close to these.
I scale my car without driver (always have) keep all lead to the left and to the rear. Try to get left side at or above
54, and rear at or around 60 at the end of the feature, I run a long wheelbase car so adding my lead to the very
back of the car doesn't make the car swing the tail like it will on a short wheelbase car,
I can get these numbers with the car weighing about 2300 after the race. On the 2 stacked leaf setup start with
around 50 to 75 Ibs heavier on the R/R tire than the l/r tire .On the r/r mono and coil deal you need to start with 100
to 150 r/r heavy. This will make your r/f tire weigh around 300 Ibs but don't get to nervous.
As far as stagger you can't get too much. I try to run 3.5 to 4"s all the
time (this will tell how good you were at copying this deal if you can't run that stager you probably didn't get it
correct). Run big tires on both fronts if your looking for more forward bite ,and small tires on both fronts if you need
the car to turn in better on fast tracks.
Wheel Offsets
I like to run all 3" offset wheels ,l do mess with that a bit, but it is backwards on this setup than any other car you
have ran, and everyone that tries to help you with tightening up your car with wheel offsets will be telling you
backwards.
Here's how it works on this deal. To make the car tighter on a dry slick track, move the l/r tire UNDER the car
more, If you want to make the car looser ,and easier to drive on a tacky heavy track move the wheel out on the l/r
and under the car more on the r/r, ,l know that sounds backwards but that's how it works on this setup ,and is
where most racers screw this deal up.
That is a good start and I will post a link to the pics again and go into the mono and coil r/r deal next, just give me some time.

P.S, to 4M please let us know when your going to dump this thread so we can copy it next time please, There were a lot of racers using it to work with this setup and you made my phone keep ringing from deleting it. I am not, nor have I made ANY money from posting on here (Just trying to help out the low budget racers.
Thanks
Scott (Scooter) May

http://photobucket.com/albums/v655/j21style/Fastboys/ Reply Reply With Quote .

BIG10
05-21-2012, 09:52 PM
Is there a website or phone # for RC RACECARS,i would like info for buying fast boy brkts.Any help woul d be appreciated.

Dirtrunner35
05-22-2012, 10:33 AM
Some where I just saw someone have the brackets for sale

outlawstreet21
05-22-2012, 04:05 PM
Southwest speed carries the right rear floater for $ 88.00.