needing mod roller.

[21BURTON]

looking to buy a mod roller doesnt have to be new something cheap will do want a 4 bar car. thanks

[bob75]

call me 815 541 9656 know were a couple cars are

[TREMod36]

I have a 2006 TRE Mod asking $3,000 there is about 30 nights on it.

[JF_70F]

Check it out do not miss out pictures on graigs list link or call jim (513) 504-3005

[Flyin Iowan]

Late 2009 Skyrocket #9275 built December 09....All shryock parts....winters QC...22 gal fuel cell....QA1's by Precision Performance....about 40 nights on car....black powder coat......Turnkey $20K....Roller $8K....car is and will be raced until sold....call Mike Zogg 563-320-6439

[rc14]

2004 Pierce Modified BP#210



I have a 2004 Bob Pierce UMP modified. It is underrail chassis #BP210. I bought it used as a bare chassis, assembled it last fall, and only ran it 6 nights. It has a 32 gallon fuel cell, Winter's 9" ford floater rearend w/31 spline axles, fresh 6.00 gear with mini spool. Rear suspension is setup clamped 4link/zlink with 15"Hyperco rear springs,BP lift bar w/6th coil & BP pullbar w/Hyperco 600/1200 spring. The C0ckpit is aluminum diamond plate floor & trans tunnel with 17" Kirkey intermediate seat,15" steering wheel, Wilwood brake/clutch pedals w/Tilton M.C.'s, Afco 2-1 steering quickner, & Autometer tach, O.T., O.P., W.T. gauges. The front end is set up with Metric spindles, Nova lower control arms & UB machine uppers with Howe low friction ball joints & Hyperco/Eibach front springs. It has Pierce/Fast Company Afco rebuildable shocks, US Brake rotors(Fr&R), US Brake oversize calipers(LF,LR&RR) and US Brake pads(Fr&R). It has a Howe aluminum radiator, Mid motor plate, GM aluminum bellhousing, Bert transmission with standard tailshaft and driveshaft. All I did was pull my motor & battery. Just add yours & the car is complete & Race Ready! I'm asking $4800 or B.O. as listed. I will sell this race car as a roller without the bert, driveshaft, shocks, seat & gear for $3500 or B.O. Sorry, no trades. I can email pictures of car. Contact Rick at (513)403-4114(if no answer, please leave msg) or email to rc14@cinci.rr.com

[cyclone20]

I have a 2007 ellis roller 4 bar z link seat rad. driveshaft 567 gr needs your motor and tran..$2750.00 call me 812-756-2604

[mighty18]

2012 Rocket by Ruhlman Roller
Car: Chevelle Front Clip, 4-Link Suspension w/ Lift Bar, assembled at Rocket Chassis - Bull Dog QC Rear w/ CM Tubes, LW Spool, Low Drag Bearings, Bearing Bird Cages - Wilwood Aluminum Metric Calipers, Pedals and Master Cylinders - Hybryd Front Rotors w/Bearing Spacers - Port City Bearing Upper Control Arms - Howe Low Friction Ball Joints - Sweet Steering Box and Collapsible Steering Shaft, all Swaged Aluminum Rods - all Teflon Rod Ends - Wiles Steel Driveshaft w/ Hybrid U Joints -- Integra Stealth Steel Mono Tube Shocks - Integra Springs - C/O Rears - 7AL MSD Box - Blue MSD Coil - Quickcar Extreme 4 Gauge Panel - Tel Tac Digital Tach - Coleman Bearing Throttle Pedal - Turbo Start 16v Battery w/ Quickcar Battery Cables and Master Disconnect - Simpson Sprint Window Net, Seat Belts - Barry Wright Style Fuel Safe Fuel Cell w/Foam and Cage - .080 Driveshaft Tunnel, Floor, Foot Box, Left Side Tunnel and Driver Door Bar Protector - Arrow Wheels and Hoosier Tires - Spare Front Bumpers included. Car is top of the line and everything built new this season $18,500.00. 304-677-3929