sports19
09-10-2012, 05:46 PM
7" Bilsteins: 3050, 6060, DP1 LF, 5050 $60 each
9" Bilsteins :3050, 4040, 3030, DP1 RR, DP1 LR $60 each
Dart Platinum 2 steel heads, about 300 laps / 12 nights since new Manley valves and new roller springs, gasket matched $900
1.89 3 speed, fresh rebuild $200
34" 31 spline axle new $70
34" 28 spline axle used $50
4.86 9" gear 28 spline full spool $250
dirtworks style rubber biscuit pull bar no heims $20
750 holley vacuum secondary carb 'stock' $50
metric header left side $20
47 1/2" drive shaft balanced for chevy driveshaft ford rear end $50
15" plastic fan $10
z28 valve springs and retainers NEW $20
X-rod 5.7 GM $10 set
clevite hydraulic cam 390 410 lift NEW $20
4" K&N air filter $20
misc upper ball joint holders $20 for all of them
custom ground comp cam 4/7 swap solid lifter for 2 barrel and crower roller rockers made for the cam $200
allstar aluminum crank hub $100
2.055 / 1.6 valves stock length $50 set used 1 year
2.055 / 1.6 valve .200 long $50 set used 1 year
2.02 / 1.6 valves stock length $40 set (used)
used BSB birdcages for shaw, welded shock mounts $175 pair
10" 2 offset 5 on 5 steel wheel, 2 beadlocks 3 regular $220 for all
***Rotating assembly (all brand new in the boxes)***
Compstar 6" H beam rods $575, Scat 4340 superlight crank 350 main 3.875 stroke $1240, ATI aluminum super damper $389, Cloyes aluminum timing cover $120, Melling anti cavitation oil pump $87, pick up tube $30, Champ CP100KO oil pan $330, Moroso oil filter adapter for oil cooler $80
ARP head stud set 4301 $200.............this stuff would be over $3250 after tax, I have a set of used JE dome pistons for these rods and crank for 4.125 bore, I want $3000 for this stuff
located in Highland, IL 618-210-3514
9" Bilsteins :3050, 4040, 3030, DP1 RR, DP1 LR $60 each
Dart Platinum 2 steel heads, about 300 laps / 12 nights since new Manley valves and new roller springs, gasket matched $900
1.89 3 speed, fresh rebuild $200
34" 31 spline axle new $70
34" 28 spline axle used $50
4.86 9" gear 28 spline full spool $250
dirtworks style rubber biscuit pull bar no heims $20
750 holley vacuum secondary carb 'stock' $50
metric header left side $20
47 1/2" drive shaft balanced for chevy driveshaft ford rear end $50
15" plastic fan $10
z28 valve springs and retainers NEW $20
X-rod 5.7 GM $10 set
clevite hydraulic cam 390 410 lift NEW $20
4" K&N air filter $20
misc upper ball joint holders $20 for all of them
custom ground comp cam 4/7 swap solid lifter for 2 barrel and crower roller rockers made for the cam $200
allstar aluminum crank hub $100
2.055 / 1.6 valves stock length $50 set used 1 year
2.055 / 1.6 valve .200 long $50 set used 1 year
2.02 / 1.6 valves stock length $40 set (used)
used BSB birdcages for shaw, welded shock mounts $175 pair
10" 2 offset 5 on 5 steel wheel, 2 beadlocks 3 regular $220 for all
***Rotating assembly (all brand new in the boxes)***
Compstar 6" H beam rods $575, Scat 4340 superlight crank 350 main 3.875 stroke $1240, ATI aluminum super damper $389, Cloyes aluminum timing cover $120, Melling anti cavitation oil pump $87, pick up tube $30, Champ CP100KO oil pan $330, Moroso oil filter adapter for oil cooler $80
ARP head stud set 4301 $200.............this stuff would be over $3250 after tax, I have a set of used JE dome pistons for these rods and crank for 4.125 bore, I want $3000 for this stuff
located in Highland, IL 618-210-3514