Kevin Santee
02-25-2013, 08:08 PM
*2001 Rocket Black Front End 2" Tube, Raised Rt. Rail Roller. Car has Winters 4:86, PPM Bearing Birdcages, Winters Hubs, BRT rack 3:9 ratio, Bicknell Calipers, newer gauges & panel switch, brake bias gauges, rt front shut off, motor plate, radiator. Comes with MSD IGNITION, w/soft touch Rev limit box & coil. Shocks either Bilsteins or Afco's, your choice. Car could use new body, but the one on it is raceable. (some extra's come w/car) $ 3950.00
*18deg Chevy Top End. Heads are HUT 1.1 CNC port design (30 laps since been freshened), Jesel shaft system (rockers may have 300 laps since new), Comp Lifters (30laps old), push-rods, Comp Cam, Chevy Bowtie intake, Nice stuff not blown up and repaired. $2900.00
*18 degJE Pistons 4.125 bore w/rings (30 laps since new) on Oliver 6.125 Rods $1000.00
*KB Gas Carb ran on 18deg engine $500.00 or trade for e-85 Carb
*10 GENISIS G1 Shocks- 8 very good condition bodies and seals 6 were rebuilt, and 2 need seals. $1400.00
* Butler Built Full Containment Seat - fits driver in 130-150 lb range for a smaller driver- $500.00
* 1984 Chevy Gruman Style Van - rebuilt engine about 5k & rebuilt tranny abt 1500miles, excellent brakes, good rubber, used to haul latemodel to Erie & Sharon last year from Raceway 7 area. $1500
* Brigdeport w/ 3phase converter motor to use in 220system. has vice too. $1100.00
* Metal Lathe- $600.00 power feed table.
* Bert Ball Spline Trans. $1000.00
* Bert Bell housing $375.00 (like new), 4 Scalloped Brake Rotors, BLP Belt Drive fuel pump, Lightweight 7mm BLP Crate pulleys w/ madrels (used 1 nite), mechanical fuel pump, 6.200 Rods, small generator, other stuff I don't know I have yet.
-----Call or Text 440-813-3359 -------Thanks, Kevin S. Feel free to make offers.
*18deg Chevy Top End. Heads are HUT 1.1 CNC port design (30 laps since been freshened), Jesel shaft system (rockers may have 300 laps since new), Comp Lifters (30laps old), push-rods, Comp Cam, Chevy Bowtie intake, Nice stuff not blown up and repaired. $2900.00
*18 degJE Pistons 4.125 bore w/rings (30 laps since new) on Oliver 6.125 Rods $1000.00
*KB Gas Carb ran on 18deg engine $500.00 or trade for e-85 Carb
*10 GENISIS G1 Shocks- 8 very good condition bodies and seals 6 were rebuilt, and 2 need seals. $1400.00
* Butler Built Full Containment Seat - fits driver in 130-150 lb range for a smaller driver- $500.00
* 1984 Chevy Gruman Style Van - rebuilt engine about 5k & rebuilt tranny abt 1500miles, excellent brakes, good rubber, used to haul latemodel to Erie & Sharon last year from Raceway 7 area. $1500
* Brigdeport w/ 3phase converter motor to use in 220system. has vice too. $1100.00
* Metal Lathe- $600.00 power feed table.
* Bert Ball Spline Trans. $1000.00
* Bert Bell housing $375.00 (like new), 4 Scalloped Brake Rotors, BLP Belt Drive fuel pump, Lightweight 7mm BLP Crate pulleys w/ madrels (used 1 nite), mechanical fuel pump, 6.200 Rods, small generator, other stuff I don't know I have yet.
-----Call or Text 440-813-3359 -------Thanks, Kevin S. Feel free to make offers.