zeroracing
09-08-2015, 07:30 PM
Random Order
2006 Swartz late model chassis and tub, has tub and some brake lines, older bumper and used nose piece. $ 750 or $ 800 with nose below.
Extra front bumper and used but great condition Dominator nose $ 100.
Afco 2.5” ID Coil Over Springs
10” Long 300, 550 (or 500 number partially rubbed off), 450, 400
12” Long 225, 225
14” Long 175, 200, 250
$ 10 Each or all nine for $ 60
Front spindle set, wide 5 late model, tall with short steering arm, unknown brand $ 25 for Both.
Front wide 5 hubs (2), bearings, covers, standard rotors. $ 75 set.
Appleton Rack with Servo, bought used from Crebo Racing Parts, they assured it worked. 19.25” long, 3.4 on it. $ 300.
Brake Pedal, Dual Howe Masters (7/8” and 1” bore) with adjuster $ 125
Winters Quick Change. 4.86 ring and pinion, 35” RR, 32” LR aluminum tubes. $ 250 Bare
$ 300 with Gun Drilled Axles
BSB Quick Change Pinion J Bar Mount, Slider style with spacers $ 100
Wilwood rear wide five hubs, bearings, 8 bolt drive flanges, drilled rotors (2 total) $ 150 for the set.
CV Products Aluminum J Bar, 5 inch Arch, Range about 17 5/8” to 19 3/4” $ 90
BSB J bar Mounts (Frame side) 2” square $ 25
1.5” square $ 15
Steel J-Bar 22”-24” $ 15
Swartz older style (pre 2013 or so) Welded Lift Arm, used for 1 lap then broke driveshaft (has a small ding the upper portion) no cracks, hauled around after as a spare. with brackets. $ 50
Steering Column - 66.75” Long, two U joints, 2 support heims, Hex Disconnect with steering hub. $ 65
Older Liner Birdcages, unknown brand, has 2 brake clamp brackets 3.5” caliper spacer, retainer rings. $ 15
Assorted Birdcage Parts - BSB Liner Cage Barrels, Brake Clamps, Lock Rings (random stuff). $ 15
Steel Birdcage and assorted parts, bob liner mod 4 link cage never used, brake clamps (one metric), stop rings. $ 30
All the Birdcage parts above on box $ 50
Spare Wilwood wide 5 hub, bare $ 5
2 Wilwood calipers, 5.5” mounts, 4 piston fits narrow rotors, not sure if dynalites or what. $ 30 for both.
Willwood Black superlite brake pads, low races on them on axle set, and one axle set of random pads or superlite. $ 30
Afco Swing Arm (short, 12.5” long w/o heim, with heim 14” long) $ 5
2 Aluminum Clevis, for linkages, never used $ 5
2 Battery boxes one 12” wide, one 10.5” $ 15 each
Kirkey 15” Seat with cover, basic seat $ 50
Gauges and Warning lights, 2 fuel pressure (only one works other does not light up), Water temp, Oil, Warning lights, Switch and push button. $ 50
Dominator Plastic Hood Scoop, Carbon Fiber look used but good $ 5
Power Steering tanks, one dented but no leaks other good $ 20 good one $ 10 Dented one
Griffen Aluminum Radiator 19” tall by 24” wide, pinhole repair, no leaks $ 50
Powertrain industries mod driveshaft 32.5” long no yoke $ 50
Edlebrock Alky Fuel Pump SBC $ 10
Carter Gas Pump $ 10
Victor Jr. Intake, good condition $ 200 firm
Bully Chrome Running boards, 68” long, not sure what truck they are for supposed to be ford. $ 50
Hitachi Mini Starter, Block Mount SBC $ 60
CVR Mini Starter, Pro torque Model $ 125
Mini Starter, Cracked mount but works $ 25
2 Carbon Fiber Beadlock 15x12 wheels, 4” BP. $ 100
Homemade spring rater, hydraulic like speedway one, 3000 # capacity, set up for coil overs but can do conventional springs with a sider. Works ok, not fancy. $ 50
SBC Water Pumps (2) Short Aluminum $ 15 each or $ 25 for both.
Moroso Blue Max ignition wires, new in box and never put together. $ 25
Pro-Pan aluminum dry sump pan, has been repaired $ 125
Axles all gundrilled, 37” & 32” for $ 25 each, 35”&34” for $ 40 each or all for $ 100
Snap On 14.4 v impact, 3/8”. Charger broke, tool works just cant recharge so stopped using, still has some charge. rough looking but great tool. $ 50
SBC Wet Sump pan, dual kickouts, dipstick, windage tray, needs good cleaning. $ 100
Fan spacers 2-2”, 1-1.75”, 1-1.5” and 1-1” all for $ 10.
Falcon used coupler $ 10
Metric brake pad spacers $ 5
Bolaws 850 cfm? alky carb apart, I think everything is here, $ 20.
2” Setback steel motor mounts (SBC) $ 5
6 blade 18” fan $ 10
Chrome 14” air cleaner assembly $ 5
3 new american racer tires, never raced, all MD 56 tires, 28.5-11.0-15R, 28.5-11.0-15DTW, and 29.0-11.0-15DTW $ 15 each.
32 gal ATL fuel cell with steel can $ 50.
I have pictures of everything, can get you measurements as needed. Call or text 417-860-4909 or message me. All prices do not include shipping and I will not ship anything that UPS will not take. Please no text or calls after 9pm central.
2006 Swartz late model chassis and tub, has tub and some brake lines, older bumper and used nose piece. $ 750 or $ 800 with nose below.
Extra front bumper and used but great condition Dominator nose $ 100.
Afco 2.5” ID Coil Over Springs
10” Long 300, 550 (or 500 number partially rubbed off), 450, 400
12” Long 225, 225
14” Long 175, 200, 250
$ 10 Each or all nine for $ 60
Front spindle set, wide 5 late model, tall with short steering arm, unknown brand $ 25 for Both.
Front wide 5 hubs (2), bearings, covers, standard rotors. $ 75 set.
Appleton Rack with Servo, bought used from Crebo Racing Parts, they assured it worked. 19.25” long, 3.4 on it. $ 300.
Brake Pedal, Dual Howe Masters (7/8” and 1” bore) with adjuster $ 125
Winters Quick Change. 4.86 ring and pinion, 35” RR, 32” LR aluminum tubes. $ 250 Bare
$ 300 with Gun Drilled Axles
BSB Quick Change Pinion J Bar Mount, Slider style with spacers $ 100
Wilwood rear wide five hubs, bearings, 8 bolt drive flanges, drilled rotors (2 total) $ 150 for the set.
CV Products Aluminum J Bar, 5 inch Arch, Range about 17 5/8” to 19 3/4” $ 90
BSB J bar Mounts (Frame side) 2” square $ 25
1.5” square $ 15
Steel J-Bar 22”-24” $ 15
Swartz older style (pre 2013 or so) Welded Lift Arm, used for 1 lap then broke driveshaft (has a small ding the upper portion) no cracks, hauled around after as a spare. with brackets. $ 50
Steering Column - 66.75” Long, two U joints, 2 support heims, Hex Disconnect with steering hub. $ 65
Older Liner Birdcages, unknown brand, has 2 brake clamp brackets 3.5” caliper spacer, retainer rings. $ 15
Assorted Birdcage Parts - BSB Liner Cage Barrels, Brake Clamps, Lock Rings (random stuff). $ 15
Steel Birdcage and assorted parts, bob liner mod 4 link cage never used, brake clamps (one metric), stop rings. $ 30
All the Birdcage parts above on box $ 50
Spare Wilwood wide 5 hub, bare $ 5
2 Wilwood calipers, 5.5” mounts, 4 piston fits narrow rotors, not sure if dynalites or what. $ 30 for both.
Willwood Black superlite brake pads, low races on them on axle set, and one axle set of random pads or superlite. $ 30
Afco Swing Arm (short, 12.5” long w/o heim, with heim 14” long) $ 5
2 Aluminum Clevis, for linkages, never used $ 5
2 Battery boxes one 12” wide, one 10.5” $ 15 each
Kirkey 15” Seat with cover, basic seat $ 50
Gauges and Warning lights, 2 fuel pressure (only one works other does not light up), Water temp, Oil, Warning lights, Switch and push button. $ 50
Dominator Plastic Hood Scoop, Carbon Fiber look used but good $ 5
Power Steering tanks, one dented but no leaks other good $ 20 good one $ 10 Dented one
Griffen Aluminum Radiator 19” tall by 24” wide, pinhole repair, no leaks $ 50
Powertrain industries mod driveshaft 32.5” long no yoke $ 50
Edlebrock Alky Fuel Pump SBC $ 10
Carter Gas Pump $ 10
Victor Jr. Intake, good condition $ 200 firm
Bully Chrome Running boards, 68” long, not sure what truck they are for supposed to be ford. $ 50
Hitachi Mini Starter, Block Mount SBC $ 60
CVR Mini Starter, Pro torque Model $ 125
Mini Starter, Cracked mount but works $ 25
2 Carbon Fiber Beadlock 15x12 wheels, 4” BP. $ 100
Homemade spring rater, hydraulic like speedway one, 3000 # capacity, set up for coil overs but can do conventional springs with a sider. Works ok, not fancy. $ 50
SBC Water Pumps (2) Short Aluminum $ 15 each or $ 25 for both.
Moroso Blue Max ignition wires, new in box and never put together. $ 25
Pro-Pan aluminum dry sump pan, has been repaired $ 125
Axles all gundrilled, 37” & 32” for $ 25 each, 35”&34” for $ 40 each or all for $ 100
Snap On 14.4 v impact, 3/8”. Charger broke, tool works just cant recharge so stopped using, still has some charge. rough looking but great tool. $ 50
SBC Wet Sump pan, dual kickouts, dipstick, windage tray, needs good cleaning. $ 100
Fan spacers 2-2”, 1-1.75”, 1-1.5” and 1-1” all for $ 10.
Falcon used coupler $ 10
Metric brake pad spacers $ 5
Bolaws 850 cfm? alky carb apart, I think everything is here, $ 20.
2” Setback steel motor mounts (SBC) $ 5
6 blade 18” fan $ 10
Chrome 14” air cleaner assembly $ 5
3 new american racer tires, never raced, all MD 56 tires, 28.5-11.0-15R, 28.5-11.0-15DTW, and 29.0-11.0-15DTW $ 15 each.
32 gal ATL fuel cell with steel can $ 50.
I have pictures of everything, can get you measurements as needed. Call or text 417-860-4909 or message me. All prices do not include shipping and I will not ship anything that UPS will not take. Please no text or calls after 9pm central.