|
|
-
Older Activity
-
03-22-2023, 06:59 PM
Yes, but no matter if it's a solid pullbar, the rear end pulling forward under hike makes the pinion rise more then a torque arm in most cases. The...
18 replies | 939 view(s)
-
03-13-2023, 01:30 PM
It was a longhorn of GR's not Austins AK car. When GR has raced the #2 car it's always been a longhorn numbered 2 and red just like Austins car....
68 replies | 13613 view(s)
-
03-08-2023, 08:35 PM
Not sure who you saw but Kelly isn't intimidating looking at all, he's pretty skinny and not overly tall. I'm sure you could google him, we always...
81 replies | 6102 view(s)
-
03-08-2023, 02:43 PM
Salina KS: Kelly dropped a guy on the front stretch after the race when they stopped the top 3 or 5 on the track for interviews and the guy came up...
81 replies | 6102 view(s)
-
03-07-2023, 04:03 PM
You saw what Frye did to Duke Whisnant, right?
81 replies | 6102 view(s)
-
03-06-2023, 03:53 PM
I should also add, it's pretty common for the RR tube to bend upwards adding camber to the RR tire (not toe in this case) from being used and ran a...
6 replies | 625 view(s)
-
03-06-2023, 03:48 PM
If you have to run a bent rear, toed out is way way better then toed in. I can tell you that for sure.
6 replies | 625 view(s)
-
03-06-2023, 03:47 PM
They are supposed to be square and no toe, however I have seen a few messed up from the factory where the bells tube hole was machined crooked and...
6 replies | 625 view(s)
-
03-02-2023, 08:49 PM
Spring surge is going to effect rebound rate/time way more then the spring being used is.
17 replies | 1327 view(s)
-
03-02-2023, 08:46 PM
Anti-dive is also caster gain during compression, So without a influence from a brake being applied you still have caster gain happening.
...
3 replies | 472 view(s)
-
02-28-2023, 12:14 PM
The other thing people are forgetting is there is no longer a 40 option for the front or LR. While it may not change things for some series, it does...
30 replies | 3116 view(s)
-
02-17-2023, 01:00 PM
I got a question:
1. Where does frank work?
2. What does frank sell?
That's a rhetorical question
17 replies | 1327 view(s)
-
02-13-2023, 11:39 AM
Prebent and prenotched tubing
15 replies | 1574 view(s)
-
02-10-2023, 01:19 PM
They measure stuff sometimes, lol
The RR still has to be at 39" at ride height, they will usually check the nose height and RR deck hieght before...
7 replies | 793 view(s)
-
02-08-2023, 10:20 PM
WoO events so not till volusia
4 replies | 1083 view(s)
-
01-31-2023, 11:25 PM
House car was off it pretty quickly from what I saw
8 replies | 1586 view(s)
-
01-31-2023, 03:27 PM
I'm not gonna study all the schedules together but looked at the belleville race and seems like they are booking races really close to other races...
22 replies | 3563 view(s)
-
01-31-2023, 02:15 PM
RR no longer has to be off ground when checking
30 replies | 5632 view(s)
-
01-29-2023, 06:04 PM
Well, they did allow the new Hoosier #1 to be ran (lm10) so you know that saved money by wearing out more tires and since they softer and have more...
12 replies | 3538 view(s)
-
01-25-2023, 02:38 PM
Whats funny is per the rule book the changes they did the back are not legal, so we'll see if they get that changed to be legal if they go on to...
41 replies | 5827 view(s)
-
01-25-2023, 02:20 PM
It was designed back in mid 2021 and was supposed to be tested in 2022 and for sale in 2023. However all that got put on the back burner and the car...
41 replies | 5827 view(s)
-
01-24-2023, 09:47 PM
3.0 between lower control arm and frame (std lowers back then with shock mount on top of tubing of the arm. assuming it has 10.375 RF tall spindles...
1 replies | 571 view(s)
-
01-23-2023, 12:34 PM
They haven't made a LM10 (#1 in the new tires) according to Mr Rush at Hoosier since 2012 or 2014 (I forget but around that time frame) so it's not...
31 replies | 4929 view(s)
-
01-16-2023, 04:14 PM
Too add to that:
I assume it says you have to have a caliper, so not running one likely isn't an option but does it say it has to be same caliper?...
14 replies | 1441 view(s)
-
01-16-2023, 02:35 PM
Does it also say no proportioning valves on RF?
14 replies | 1441 view(s)
-
01-12-2023, 08:43 PM
I can't give you that measurement unless we are comparing the same chassis.
Not all cars have the upper rails parallel to the Jig or whatever you...
4 replies | 935 view(s)
-
01-12-2023, 08:24 PM
As long as you are 87 degrees at the RR corner of the car, you will just make the 117" required minimum on the diagonal measurement.
Now there are...
4 replies | 935 view(s)
-
01-10-2023, 01:04 PM
There are so many variable to what is better on a given situation but I'm gonna go along the lines and define some stuff like MB did above:
...
25 replies | 2008 view(s)
-
01-10-2023, 12:34 PM
It can do 2 things really:
1. Adding compliance to the drive train, just like a 5th coil does. Now is that a good idea? One could argue that's it...
3 replies | 1104 view(s)
-
01-03-2023, 11:46 AM
Hard for me to remember the exact amount but we won 5 or 6 MLRA races with the double RR and think one of them was the precursor to the silver dollar...
24 replies | 3588 view(s)
About billetbirdcage
- Biography:
- Taylormade Proformance
- Location:
- Kansas
- Interests:
- Racing
- Occupation:
- Manufacturer of LM parts
Total Posts
- Total Posts
- 1,845
- Posts Per Day
- 0.32
Visitor Messages
- Total Messages
- 1
- Most Recent Message
- 11-10-2015 03:40 PM
General Information
- Last Activity
- 03-22-2023 07:02 PM
- Join Date
- 05-15-2007
- Referrals
- 0
All times are GMT -5. The time now is 03:50 AM.
|
|
Find latest posts
03-22-2023, 06:59 PMYes, but no matter if it's a solid pullbar, the rear end pulling forward under hike makes the pinion rise more then a torque arm in most cases. The...18 replies | 939 view(s)