|
|
-
Older Activity
-
07-23-2024, 03:47 PM
Quick run down without knowing if you have just a simple single spring with no bump.
1. Record how far your adjuster nut is down from the top of...
1 replies | 168 view(s)
-
07-23-2024, 03:23 PM
Was a 90's Rayburn RR shock mount in the right place to start with? LOL
10 replies | 629 view(s)
-
07-23-2024, 03:17 PM
Holy change BATMAN, lol
2" down is a freaking huge change. Does the car lay on the RR now and tote the LF pretty good?
I've seen many cars that...
10 replies | 629 view(s)
-
07-19-2024, 09:21 PM
I can tell you the cars today have so much grip and power, that your reaction time plays a big role and we all know that dwindles as you get older...
4 replies | 792 view(s)
-
07-12-2024, 01:59 PM
If you do nothing but move the top of the RR coilover outboard, it will free entry not tighten it.
11 replies | 1113 view(s)
-
07-08-2024, 05:31 PM
XR1 is 8 3/4 on frame but 5/8 below on pinion, not sure how much lower you go then that
11 replies | 1113 view(s)
-
07-08-2024, 04:09 PM
More then likely its you, but not in the way you think or necessarily a bad thing.
It's likely your driving style, I'm gonna assume you don't bend...
11 replies | 1113 view(s)
-
07-03-2024, 09:23 AM
Then only reason I would use a progressive spring over a stack would be because of a rule that you had no choice but to use a progressive to get a...
4 replies | 575 view(s)
-
07-03-2024, 09:15 AM
As masters said, you are just gonna have more power steering with the .220 then you had with the .235
3 replies | 277 view(s)
-
05-29-2024, 01:13 PM
Say your ride pin to pin is 20"
Changing rates but keeping similar load at 18" will be different then changing rates and keeping ride load the...
8 replies | 1745 view(s)
-
05-29-2024, 12:56 PM
I got involved around 1990 so anything before that isn't going to be picked by me from lack of knowledge. That being said, I have to go with the 1996...
17 replies | 1457 view(s)
-
05-20-2024, 03:14 PM
We are pretty dominate at a track like that and typically I don't change wheel base at all there.
6 replies | 1292 view(s)
-
05-08-2024, 01:24 PM
As far as seeing the RF being down less: Depending where you are seeing this (IE on corner entry or after they are back hard on the gas), there could...
8 replies | 1395 view(s)
-
05-08-2024, 01:13 PM
Couple things to keep in mind on chain length: depending where you are on the curve of the arc of the 4 link when your stopping travel while you may...
8 replies | 1395 view(s)
-
04-23-2024, 02:43 PM
Figuring out what the real problem is always the hardest part, having said that. . . .
If the left and rear % are correct to what the chassis...
16 replies | 3311 view(s)
-
04-03-2024, 02:01 PM
Simulate what?
I can check deck hieght like they do on the droop check and me right on the 51" legal limit and then put the car at actual race...
13 replies | 3049 view(s)
-
04-02-2024, 02:39 PM
We race a bunch of different series, some do droop some do deck hieght, it's simpler and easier to NOT adjust the LR chain length (to not mess with...
13 replies | 3049 view(s)
-
04-02-2024, 12:35 PM
Tony, Typically if they are using a droop rule the ride hieght deck measurement isn't used or checked. Lucas or WoO only check the RR at ride height...
13 replies | 3049 view(s)
-
04-01-2024, 10:03 PM
Yes, it is.
13 replies | 3049 view(s)
-
02-22-2024, 01:13 PM
Replied to PM
20 replies | 8059 view(s)
-
02-21-2024, 05:36 PM
I have another way that should work way better and be really hard for tech to see or figure it out, but don't want to post here for everyone to see....
20 replies | 8059 view(s)
-
02-21-2024, 04:12 PM
Try this so a restrictor doesn't keep the brake on
Red is the restrictor and blue is a one way valve to release pressure around the...
20 replies | 8059 view(s)
-
02-15-2024, 04:04 PM
So your saying after spending 850K on a new hauler, I need to spend more and get a 100 Ton AC unit and a 1,000,000 BTU heater for the trailer to...
59 replies | 25342 view(s)
-
02-07-2024, 12:23 AM
A friend at one of the big companies saw this post and reached out to me thru a text since he isn't registered here.
Here is what he had to say:...
9 replies | 3428 view(s)
About billetbirdcage
- Biography:
- Taylormade Proformance
- Location:
- Kansas
- Interests:
- Racing
- Occupation:
- Manufacturer of LM parts
Total Posts
- Total Posts
- 1,954
- Posts Per Day
- 0.31
Visitor Messages
- Total Messages
- 1
- Most Recent Message
- 11-10-2015 03:40 PM
General Information
- Last Activity
- 07-23-2024 03:50 PM
- Join Date
- 05-15-2007
- Referrals
- 0
All times are GMT -5. The time now is 09:46 PM.
|
|