|
|
-
Older Activity
-
02-25-2021, 08:32 AM
Ships in a week from today
https://www.jegs.com/i/Dart/301/10510020P/10002/-1#
3 replies | 189 view(s)
-
02-18-2021, 12:37 PM
Correct,
Making the hole bigger, means the stud/pin will go further into the hole.
10 replies | 750 view(s)
-
02-10-2021, 09:48 AM
Braided lines are plastic too with a SS outer fabric.
I do plastic, change it every couple years. Be smart where you run it and tie it down well...
12 replies | 1083 view(s)
-
02-03-2021, 10:44 AM
Wait a minute, the 1210-102 is a 10' stud, not 7 degree. 3.848 long
10 replies | 750 view(s)
-
02-01-2021, 11:34 AM
I don't mess with Cotter keys. BUT....I also check them every week as part of the maintenance. If you have full thread engagement of the castle nut,...
10 replies | 750 view(s)
-
01-28-2021, 02:38 PM
Dart had me on the A8
4 replies | 535 view(s)
-
01-27-2021, 11:29 AM
depending the MC you are using, I have an old one I drilled a 9/16 hole in it, fitted a tire valve, Then use a locking air chuck and apply 20psi to...
7 replies | 606 view(s)
-
01-26-2021, 02:02 PM
I put a 1/4" rubber vacuum line over the bleeder screw and crack it open a 1/2 turn. Stick the other end of the hose into a container with enough...
7 replies | 606 view(s)
-
01-20-2021, 05:17 PM
What head?
4 replies | 535 view(s)
-
01-18-2021, 11:08 AM
Think about where the bar is applying the loads from the chassis.
Moving the bar from the RS of the pinion to the middle moves the loads about 1.5"...
2 replies | 624 view(s)
-
01-04-2021, 10:46 AM
I talked to a local track about renting for a day and they told me $1000 dollars.
That plus fuel and tires and all that made it out of reach. I was...
10 replies | 1136 view(s)
-
11-25-2020, 12:53 PM
Ask for dyno sheets, If they can't produce them and are current assume they need rebuilt and add that to the cost of the deal and compare to buying...
9 replies | 1562 view(s)
-
11-18-2020, 10:21 AM
You have to call them first to get an RA number. You track it through the process with the RA number so make sure it's clearly seen and can't rub off...
3 replies | 992 view(s)
-
11-16-2020, 02:06 PM
Chad hang outs on Hotrodders, Yellowbullet and Speedtalk often.
All are online forums.
5 replies | 1243 view(s)
-
11-16-2020, 02:04 PM
Everything a person needs to know right here.
https://afdc.energy.gov/fuels/ethanol_production.html
Most E85 pumps around here, as most are now,...
4 replies | 1172 view(s)
-
11-11-2020, 02:29 PM
I buy from a local station that refills weekly. It's a blender pump station. I always use the same pump. It's always right at 70 percent. I bought a...
4 replies | 1172 view(s)
-
11-02-2020, 10:46 AM
On this topic I bought my QM from a guy, that was his spare and not used. I had it apart a silly coned it shut, sealing off water/dirt. It's been...
23 replies | 4111 view(s)
-
10-27-2020, 10:32 AM
Howe and QA1 have it listed on the web sites by dimension. You can also download the catologue and dig through it or measure yours and call them. QA1...
3 replies | 827 view(s)
-
10-15-2020, 02:10 PM
Possible electrolysis. Make sure you have good shiny clean electrical grounds and even adding the OEM braided strap from engine to chassis is NEVER a...
6 replies | 1908 view(s)
-
10-09-2020, 11:03 AM
Maybe helpful I don't know But I use AWG 2 welding ground cable(stranded) and solder the ends on. I use Dialectric grease on all the connections. I...
23 replies | 4111 view(s)
-
09-29-2020, 04:29 PM
Well, this was real handy last week. The radiator cap is bad and the engine slowly lost it water. The pressure light came on the last lap but the...
15 replies | 1881 view(s)
-
09-25-2020, 05:41 PM
20 percent or more isn't unusual on a .030 GM block if it's not been honed with a torque plate. I'd send it.
A teaspoon of engine oil in the...
5 replies | 1243 view(s)
-
09-21-2020, 11:12 AM
Optimum front end will depend mostly on driving style and what you want the back end to do. Think total combination.
19 replies | 2315 view(s)
-
09-14-2020, 11:16 AM
I went to a MLRA event last week and the winner drove the car turning left most of the time. I'm sure the RR was bald a baby's butt but he also won...
8 replies | 1817 view(s)
-
09-03-2020, 04:58 PM
I was the tech guy for two local tracks. Both UMP at the time. Niether liked my style nor did UMP so that ended and I went back to racing my own car....
17 replies | 2069 view(s)
-
09-03-2020, 01:37 PM
I read a book on performance driving. IT catered to asphalt but still had some good take always.
This particular F1 driver was 1.5 seconds faster...
17 replies | 2069 view(s)
About Lizardracing
- Do you go to races?:
- ?????
Total Posts
- Total Posts
- 692
- Posts Per Day
- 0.17
General Information
- Last Activity
- 02-26-2021 12:40 PM
- Join Date
- 09-10-2009
- Referrals
- 0
All times are GMT -5. The time now is 05:53 AM.
|
|
Find latest posts
02-25-2021, 08:32 AMShips in a week from today https://www.jegs.com/i/Dart/301/10510020P/10002/-1#3 replies | 189 view(s)