|
|
-
Older Activity
-
05-18-2013, 08:03 AM
How does going to the inner RR mount help side bite. It would be less effective spring rate because of increased angle correct?
5 replies | 816 view(s)
-
04-28-2013, 08:51 PM
If you are showing cracks in 15 nights of racing with this crank you are overpowering the crankshaft or it was not balanced correctly
12 replies | 988 view(s)
-
04-13-2013, 07:50 AM
Cold settings are normally set .004 tighter but depends on the head.Set .004 tight cold then recheck when hot.
3 replies | 451 view(s)
-
04-12-2013, 08:24 AM
Got some heli-coils from Brodix one time they were about an inch long fixed the problem.
4 replies | 463 view(s)
-
04-07-2013, 06:17 PM
Thats what Gibbs is saying to do. Besides you ever see the filters on the cup cars, its at least twice as big in diameter and a little bit longer....
11 replies | 995 view(s)
-
04-07-2013, 01:08 PM
The semi-synthetic Gibbs oils are 300 lap oils. The full synthetic Gibbs oils are 500 lap oils. Both need a new filter every 100 laps and topped off.
11 replies | 995 view(s)
-
04-07-2013, 01:02 PM
Crane boxes are within 30 RPM of the setting a MSD is usually 200 short.
3 replies | 469 view(s)
-
04-04-2013, 10:24 AM
Does the pump have a high volume pressure section. Aluminum engines need more volume because of more internal pressure losses.
3 replies | 587 view(s)
-
03-31-2013, 01:20 PM
Personally don't think the smell of E85 is much better. You will lose 30-40 on the torque end and 20-30 HP if this is an open motor. A crate will...
11 replies | 741 view(s)
-
03-30-2013, 05:19 PM
.022 top/.024second could be a little tighter, but these would be safe as long as you are not using KB Pistons.
1 replies | 324 view(s)
-
03-28-2013, 07:16 PM
Don't remember think it was around $60.00.If you got someone who is good on a crank grinder they could do it too. Just have to go slow and not push,...
3 replies | 306 view(s)
-
03-27-2013, 07:30 PM
Could also be a 1.875 journal cam.50MM is 1.969 inches.55MM is 2.165 inches, measure the cam main journals. Stock cam is 1.868, I had Comp grind a...
3 replies | 306 view(s)
-
03-23-2013, 07:42 AM
Right Stuff sealer works good too, not cheap though.
8 replies | 838 view(s)
-
03-23-2013, 07:39 AM
My mastersbilts have been trailed about 5/8". The last one I got I had them build it with the LR mounts back that amount and with the rear square...
5 replies | 995 view(s)
-
03-17-2013, 01:01 PM
My local tranny shop has a cleaner for coolers, it has a filter on it. They run fluid through the cooler and keep checking the filter till it comes...
7 replies | 701 view(s)
-
03-16-2013, 08:28 AM
Use the 1182 crank, the cast crank is a pos.
12 replies | 988 view(s)
-
03-10-2013, 10:26 AM
Comp-Cam has a spring that is the clone of the stock spring only better material. Cost is around $200.00
2 replies | 646 view(s)
-
02-15-2013, 08:43 AM
Thanks for the info, never been a fan of babbitt cam bearings and looks like Durabond is the only one that makes these bearings
2 replies | 456 view(s)
-
02-13-2013, 08:28 AM
What head and rod lenth
2 replies | 89 view(s)
-
02-12-2013, 09:29 PM
Anybody used the GMP-55-HP cam bearings. Thinking of doing a 55MM cam wth these bearings but worried they will not hold up. Thanks
2 replies | 456 view(s)
-
02-11-2013, 06:57 PM
Have a NEW set of Mahle Pro series 4.165 bore 1.125CH 2.6CC dome with pins, locks & rings. $650.00
1 replies | 59 view(s)
-
01-22-2013, 08:29 AM
If its a bowtie or Little M Block that have not been lightened you are will not get down to 2300 pounds and get the correct percentages.
9 replies | 621 view(s)
-
01-13-2013, 04:10 PM
Guess I better make sure my CBN cutters are sharp and I'm stocked up on grinder wheels! Thanks
16 replies | 1137 view(s)
-
01-13-2013, 03:22 PM
What the weight savings in pounds? Need to shave some weight off a bowtie block.
16 replies | 1137 view(s)
-
01-07-2013, 06:41 PM
I have a set of Mahle Pro-series 4.165 bore for your combo. They have a .200 dome with a effective dome volume of 2.6CC.They are brand new with...
5 replies | 552 view(s)
-
01-06-2013, 10:29 PM
You got spray bar covers? If so I wouldn't run less than a three gallon tank with a good oil cooler.
2 replies | 444 view(s)
-
01-03-2013, 06:21 PM
Don't think they even have these anymore.
3 replies | 523 view(s)
-
12-30-2012, 11:05 AM
Also they internally balanced on the front and external on the flywheel end. Uses the same flywheel as a 602 or 604.
21 replies | 2289 view(s)
-
12-26-2012, 09:30 PM
Take all the rockers off the engine to take pressure off the springs. This will also seat the valves to keep the valve seats from rusting. I go and...
8 replies | 1009 view(s)
-
5 replies | 911 view(s)
About SLM98
- Do you go to races?:
- yes
Total Posts
- Total Posts
- 200
- Posts Per Day
- 0.15
General Information
- Last Activity
- 05-18-2013 08:04 AM
- Join Date
- 09-14-2009
- Referrals
- 0
All times are GMT -5. The time now is 08:41 AM.
|
|
Find latest posts
05-18-2013, 08:03 AMHow does going to the inner RR mount help side bite. It would be less effective spring rate because of increased angle correct?5 replies | 816 view(s)
