|
|
-
Older Activity
-
05-12-2013, 08:47 AM
I would stay away from it. It'll be lean unless it's been fixed from what I've seen.
3 replies | 204 view(s)
-
05-11-2013, 08:28 AM
Should be around 3 feet.
15 replies | 848 view(s)
-
04-12-2013, 06:03 PM
Try a good 4412 or even a stock one.
41 replies | 1693 view(s)
-
03-14-2013, 09:45 PM
Advertised cfm isn't a good way to choose one. Measurements and knowing what works for the application is the best way.
8 replies | 981 view(s)
-
03-06-2013, 02:07 PM
Depends on what is limiting the usable rpm. It should be the carb with a 2bbl, but you have to consider valve springs, cam, heads, manifold, etc. etc.
5 replies | 533 view(s)
-
02-22-2013, 07:15 AM
Another vote for the vortecs. The combustion chamber is smaller with the vortecs and it's a better cylinder head.
6 replies | 725 view(s)
-
02-22-2013, 07:13 AM
To answer your question, the 830 has a bigger venturi and a chamfered base plate bore. 830's were designed for restrictor plate use and are sort of...
2 replies | 252 view(s)
-
02-14-2013, 02:30 PM
6 carbs tested, 4 gas, 2 E-85, Shell premium pump GAS base line with 10% ethanol and numbers from best carb. We then picked up a little bit with...
7 replies | 895 view(s)
-
02-14-2013, 12:15 PM
E-85 will make more torque than pump gas. E-98 will not on a 602 so...sort of right.
7 replies | 895 view(s)
-
02-08-2013, 09:56 AM
You'd better look them over. That's cheap.
15 replies | 1262 view(s)
-
02-08-2013, 09:51 AM
You can buy one once or buy it twice when you feel like you don't have enough snuff. I'd get a good one.
10 replies | 688 view(s)
-
02-07-2013, 11:42 AM
E-85 works great with the right parts. You can't cobble something together and expect it to work right. You can't use a gas carb. You can't use a...
7 replies | 895 view(s)
-
02-05-2013, 07:37 AM
JDR, Stealth or Willy's. They'll work well and you would have good resale value.
2 replies | 253 view(s)
-
02-03-2013, 09:37 PM
They're good people and not beginners.
5 replies | 900 view(s)
-
02-02-2013, 12:16 PM
I wouldn't shop for one based on flow numbers, especially anything used! You'll probably end up with the wrong thing if you do. Call a carb builder...
7 replies | 691 view(s)
-
01-31-2013, 11:57 AM
Check your pm rmrc.
67 replies | 5261 view(s)
-
01-30-2013, 10:38 AM
That's interesting too. I do have a couple of questions though. Other than the obvious advantage of being able to speed up production by mig welding...
67 replies | 5261 view(s)
-
01-30-2013, 08:22 AM
That's interesting information on the aircraft manufacturing. Be careful though, you provided too many facts and some mongoloid will probably want to...
67 replies | 5261 view(s)
-
01-22-2013, 10:14 PM
Float set too low? Small inlet fitting? Sat after being freshened or ran?
17 replies | 1253 view(s)
-
01-19-2013, 08:45 AM
You got a good one then. They're hit and miss but they're pretty.
5 replies | 1124 view(s)
-
01-18-2013, 03:51 PM
I'll agree with that.
67 replies | 5261 view(s)
-
01-18-2013, 02:22 PM
Why not post it? If it's a good way to do it maybe it'll keep people from getting hurt.
67 replies | 5261 view(s)
-
01-18-2013, 12:21 PM
Oh. I'm a fool. This comes from a guy that quotes Forrest Gump, can't spell or use correct grammar, and has contributed nothing constructive to the...
67 replies | 5261 view(s)
-
01-18-2013, 07:46 AM
It seems like you'd have a lot of oddball parts. I would probably try to lose weight elsewhere.
16 replies | 1137 view(s)
-
01-17-2013, 10:19 AM
Everything I said was 100% accurate and can be confirmed with even minimal effort. The type of rod, shielding gas, and procedure is what is used in...
67 replies | 5261 view(s)
-
01-16-2013, 11:29 AM
Like I said, make the call. I could make you look real ignorant right now but I'm not into whizzing contests. Pride and stupidity are found together,...
67 replies | 5261 view(s)
-
01-16-2013, 10:55 AM
I guarantee you that you've never been in a shop building pro drag cars and mig welding 4130. A simple call to NHRA would let you know that you can't...
67 replies | 5261 view(s)
-
01-16-2013, 10:41 AM
Nobody said that you were the Boo Boo, but... As long as the person welding the car up is also driving it have at it. If you're building chassis for...
67 replies | 5261 view(s)
-
01-15-2013, 08:06 PM
I have heard that aircraft manufacturers mig weld it too but it isn't done by Boo Boo with his 110 buzz box. Tig welding lets you back the heat off...
67 replies | 5261 view(s)
Total Posts
- Total Posts
- 757
- Posts Per Day
- 0.35
Visitor Messages
- Total Messages
- 1
- Most Recent Message
- 05-13-2012 07:34 AM
General Information
- Last Activity
- 05-17-2013 12:34 PM
- Join Date
- 06-28-2007
- Referrals
- 0
All times are GMT -5. The time now is 02:20 PM.
|
|
Find latest posts
05-12-2013, 08:47 AMI would stay away from it. It'll be lean unless it's been fixed from what I've seen.3 replies | 204 view(s)
