|
|
-
Older Activity
-
05-31-2013, 12:14 PM
I know some let the air out of the tires when new for a few heat cycles to lock in stagger.
3 replies | 368 view(s)
-
05-31-2013, 12:02 PM
Wallace and shrader awesome. Cry baby Stewart not so much. Stay home.
1 replies | 122 view(s)
-
05-28-2013, 12:30 PM
I had a very similar problem and it ended up being my timing. My distributor moved just enough that it would start fine cold but when warmed up if it...
8 replies | 422 view(s)
-
05-22-2013, 02:18 AM
I was thinking adding 5 gallons of fuel and maybe 1lb out of the rr. I don't want to do too much and ruin what I have. I can finally race with the...
8 replies | 1232 view(s)
-
05-21-2013, 10:32 AM
What are some of the adjustments you guys are making to tighten up your cars for the feature. Its a 4 bar metric impressive. The car is a turd in the...
8 replies | 1232 view(s)
-
05-08-2013, 01:58 AM
Brian the best thing I started doing was trusting what I had and just driving it like a car. That whole deal with setting the car with the brake is...
7 replies | 1964 view(s)
-
05-05-2013, 06:44 PM
Why does moving pullbar shock side to side change anything?
6 replies | 398 view(s)
-
05-05-2013, 12:34 PM
Just a quick update. I made my own dummy pull bar shock and it made a HUGE difference in freeing up my entry! I actually had to take some of the...
5 replies | 839 view(s)
-
05-05-2013, 12:49 AM
Moved llb up 1 hole on chassis and way too loose
Moved rlb up one hole on chassis and 4 wheel slide
Swapped in a dummy pull bar shock and the car...
8 replies | 774 view(s)
-
05-03-2013, 08:26 PM
Man I just wish I could get a Handel on this base setup and feel comfortable driving this animal. I'm getting a ton closer but am sick of fighting...
8 replies | 774 view(s)
-
05-03-2013, 03:44 PM
When I try to pick up the throttle just before the apex it wants to move up. Should I move the top bar back up at the chassis along with the bottom...
8 replies | 774 view(s)
-
05-03-2013, 01:21 PM
Btw I'm 200hp down on everyone else. Very mild motor .
8 replies | 774 view(s)
-
05-03-2013, 01:19 PM
Right now I have a tight loose condition and am trying to make the car rotate in the middle without mashing the gas. My lr top bar is in the third...
8 replies | 774 view(s)
-
05-01-2013, 11:12 PM
Heard from a few racers it was the roughest track they've ever been on.that's crazy cause I've seen butler pretty bad. I wait a week or two and see...
9 replies | 582 view(s)
-
05-01-2013, 09:55 PM
Man I just might have to make some special trips down there this year. Sounds like a awesome deal for the drivers in every class.
9 replies | 582 view(s)
-
05-01-2013, 12:19 PM
The b money deal is awesome. Espically for us newer or slower cars. Usually the b means tore up cars and no payouts just to try and make the a....
9 replies | 582 view(s)
-
04-29-2013, 05:26 PM
I don't think there's a single carnat our track that runs foam anymore.
29 replies | 1567 view(s)
-
04-29-2013, 05:20 PM
"yes" I would use pinto spindles on nova lowers because there stronger. I have been seeing a lot more metric cars with nova lowers running metric...
8 replies | 449 view(s)
-
04-28-2013, 12:58 PM
I just wanted to bump this thread for any new drivers out there. It helped me a ton last year.
7 replies | 1964 view(s)
-
04-27-2013, 11:00 PM
68-72
Wider
Yes
8 replies | 449 view(s)
-
04-23-2013, 01:38 AM
Depends if your trying to gain stagger or not.
4 replies | 725 view(s)
-
04-22-2013, 01:16 PM
I forgot about the ign switch. Will have to remember that one.
7 replies | 398 view(s)
-
04-20-2013, 10:55 AM
I Kept that to myself but now that it's out there lol!!
20 replies | 1537 view(s)
-
04-19-2013, 05:17 PM
I think I had a bad coil? It's still fairly new but I swapped in my old junker and it fired right up. Any way to test a coil?
7 replies | 398 view(s)
-
04-19-2013, 02:59 PM
I'm trying to fire my motor and loosing spark. I get a good spark for the 1st couple of revolutions and then nothing. I've tried new cap and rotor...
7 replies | 398 view(s)
-
04-19-2013, 06:25 AM
On my car what made the biggest difference was moving the j bar up 1 hole on the pinion. No matter what I did I couldn't get the feel I wanted but...
20 replies | 1537 view(s)
-
04-18-2013, 10:56 AM
Another suggestion starts at post #1 and start reading and saving info. It's helped me a TON!!!
20 replies | 1537 view(s)
-
04-18-2013, 09:49 AM
Before you change anything how are you entering the corner and driving thru. These cars need driven hard to work right. I struggled with the same...
20 replies | 1537 view(s)
-
04-17-2013, 06:35 PM
ruhlman does it at spartan every now and then. dosent look like he changes much. tire hikes and huge ammounts of wheel hop. awesome to watch though.
2 replies | 286 view(s)
-
04-15-2013, 09:30 PM
stock block 400's will work if done right and the procomps will also work if there a good set. like anything else preperation and attention to detail...
3 replies | 365 view(s)
- Age
- 32
About jsf74
- Do you go to races?:
- Yes
Total Posts
- Total Posts
- 316
- Posts Per Day
- 0.47
Visitor Messages
- Total Messages
- 1
- Most Recent Message
- 06-10-2012 05:31 PM
General Information
- Last Activity
- 06-18-2013 12:14 PM
- Join Date
- 08-14-2011
- Referrals
- 0
All times are GMT -5. The time now is 06:32 AM.
|
|
Find latest posts
05-31-2013, 12:14 PMI know some let the air out of the tires when new for a few heat cycles to lock in stagger.3 replies | 368 view(s)
