|
|
Search:
Type: Posts; User: stittracer99
Search:
Search took 0.18 seconds.
-
Yep our driver side valve cover is vented. I don't have any pics and didn't even see the bearings first hand. My dad was at the engine shop when they tore it apart and saw them. He said they went...
-
About 14.5:1 compression. Dyno'd 733 HP. So I guess it's possible, but I've talked to other guys running Eagle stuff with good success.
And also I am using the steel braid with the screw together...
-
Eagle crank, Dyers rods, Champ pan
-
It's a Wulff pump and I don't remember exactly which adapter it is, but it takes the large racing filter (like a Fram HP6) and it has four total oil ports (two on each side). We did verify that it...
-
Ran two laps because that's all the longer our warm up session was (thankfully) and it ran normal the whole time, still had 20 lbs oil pressure at idle when it shut off. Oil temp had built enough to...
-
We run on alcohol and always let the car run in the pits at idle for 5+ minutes to get the oil and water temps up before going out and running at race speed. Is it enough to damage the engine even at...
-
So here's the deal...all aluminum DLM dry sump engine (Brodix block) on a fresh professional rebuild. Ran 2 laps in warm ups and checked the Oberg filter and it was PACKED with bearing material....
-
What is the correct measurement for the lateral location of the rear on a Rocket. Need the measurement from the right frame rail to the 90/10 shock bracket on the rear. I have a Rocket book that...
-
yes pajamie, you are right. the 11.0/29.0-15 is the white dot and it is supposed to fire faster. also, the NRM stands for "new rib mold". Hoosier recommends using these tires for most side bite...
-
I have a very nice BRC 3.800" crank for a small block Chevy. 2.100" rods with 2.448" (350) mains. Standard size on both. This crank was just polished and checked out fine. Would make a great 410...
-
I have a very nice BRC 3.800" crank for a small block Chevy. 2.100" rods with 2.448" (350) mains. Standard size on both. This crank was just polished and checked out fine. Would make a great 410...
-
I'm looking for one 7" used gas canister shock. Either M2 or Silver series. I'm not looking to buy a complete set as I don't have the money to do that right now. Let me know what you have.
Thanks...
-
-
-
-
-
-
First off we run a BRT rack w/ servo and a power steering pump mounted on the front of the block.
We have been having issues with "tight" steering on and off for the last month. The first time I...
-
I have a COMPLETE set of Brodix 11x aluminum spread port heads. The heads have roller valve springs with titanium retainers and stainless steel 2.15 intake and 1.60 exhaust valves. The heads have...
-
-
I have a COMPLETE set of Brodix 11x aluminum spread port heads. The heads have roller valve springs with titanium retainers and stainless steel 2.15 intake and 1.60 exhaust valves. The heads have...
-
-
I have a COMPLETE set of Brodix 11x aluminum spread port heads. The heads have roller valve springs with titanium retainers and stainless steel 2.15 intake and 1.60 exhaust valves. The heads have...
-
-
I have a set of 6" Manley large journal H-beam rods. They've never been used. Rods have 7/16" ARP bolts and Manley rates them good to 725 HP. Asking $300. 717-215-4348. Thanks for looking.
All times are GMT -5. The time now is 01:09 AM.
|
|