Search:

Type: Posts; User: C10

Page 1 of 11 1 2 3 4

Search: Search took 1.16 seconds.

  1. Thread: Mud removal!

    by C10
    Replies
    16
    Views
    5,070

    Spanky is correct D McD showed us this at the...

    Spanky is correct D McD showed us this at the shop one night and swears by it
  2. Replies
    3
    Views
    910

    Kasse heads are some of the best heads I have used

    Kasse heads are some of the best heads I have used
  3. Correct Confused, It mattered in texas as this is...

    Correct Confused, It mattered in texas as this is the state that prompted this rule. A rearend DID IN FACT fall out of a car with NO contact. It was found that one if not 2 bolts were missing from...
  4. Its not a bs call at all. I was a local track...

    Its not a bs call at all. I was a local track IMCA tech for 4 years. The loose bolt issue is widely popular and there was a bulletin sent out 2 years ago about this issue, there is a torque spec for...
  5. Replies
    6
    Views
    2,380

    a TON of stagger. WE were so tight even after...

    a TON of stagger. WE were so tight even after freeing the car up we went to 8 inches to get it to turn on the throttle, and SLAM it into the corner as hard as humanly possible, dont be afraid of it
  6. Replies
    4
    Views
    1,752

    Tap the thread holes out for holley jets prob...

    Tap the thread holes out for holley jets prob solved
  7. Thread: Motor advice !

    by C10
    Replies
    13
    Views
    2,543

    and your rocker studs should be 7/16

    and your rocker studs should be 7/16
  8. Replies
    3
    Views
    1,321

    we ran Landrums, used a set of afcos once and...

    we ran Landrums, used a set of afcos once and seemed good to go but changed them quicker then the Landrum so we went back to them. This was on a 3000 pound limited Late with Monos.
  9. Thread: 3 wheelin?

    by C10
    Replies
    16
    Views
    4,130

    I agree Jeff. And I wonder where Dominator got...

    I agree Jeff. And I wonder where Dominator got the fuel cell idea from?
  10. Replies
    4
    Views
    1,413

    oh im sorry, I read it as he was not using a...

    oh im sorry, I read it as he was not using a shroud, if you have a good shroud with the fan tight to the opening, and half in half out, then the distance is not so critical as long as it is sealed...
  11. Replies
    4
    Views
    1,413

    According to Dale McDowell at the driving school,...

    According to Dale McDowell at the driving school, 5/8 to 3/4 was the magic number.
  12. Replies
    12
    Views
    3,432

    Well I guess then that Tom Gutowski, Kirk...

    Well I guess then that Tom Gutowski, Kirk Neihouse, myself, and the other IMCA techs should stop looking for them then.
  13. Replies
    12
    Views
    3,432

    Must be unaltered OEM, with unaltered OEM pump,...

    Must be unaltered OEM, with unaltered OEM pump, original bellhousing and minimum 10 inch diameter torque converter containing a minimum of three quarts of fluid - $150
    fine if illegal. Torque...
  14. Replies
    12
    Views
    3,432

    A dummy converter is NOT IMCA legal.

    A dummy converter is NOT IMCA legal.
  15. Yeah cus it would be really lame if racing A mods...

    Yeah cus it would be really lame if racing A mods came down to driver skill and set up skills vs cubic inches....and $$$.

    I couldnt agree with you more Jeff. IMCA a mod racing up until 5 or 10...
  16. There will be no major changes for 2014 other...

    There will be no major changes for 2014 other then some things that once were a #2 infraction in the rule book (deficiency slip) will now be a dq. If you have a 2013 book, you can build your cars off...
  17. Replies
    4
    Views
    2,198

    I personally would put lf, 950 rf 900 and 200...

    I personally would put lf, 950 rf 900 and 200 across the rear, a little split for getting off the gas to help the turn in and not loose so much side bite on the RR and 200 in the rear for off the...
  18. Thread: 2.3 timing

    by C10
    Replies
    6
    Views
    1,431

    it all depends where your dizzy stops advancing...

    it all depends where your dizzy stops advancing at. Find that point, usually around 3000 if its set up right, then make your base timing from there.
  19. Replies
    7
    Views
    1,708

    IT should be rebuilt and have your builder put a...

    IT should be rebuilt and have your builder put a stiffer detent spring in it as well. I do this with all the sags I build
  20. Replies
    8
    Views
    2,647

    62, you are correct, major brain fart there,...

    62, you are correct, major brain fart there, sorry lol
  21. Replies
    8
    Views
    2,647

    untill 2000 or 2001? The new body style was just...

    untill 2000 or 2001? The new body style was just that, a new body style, they were still a fox body chassis.
  22. Thread: rule rumors?

    by C10
    Replies
    16
    Views
    4,633

    Most everything you have been hearing is rumors,...

    Most everything you have been hearing is rumors, Until I hear anything what so ever, they are all just internet chatter. Thanks, Sean Walker IMCA Tech.
  23. I have a scanner on my smart phone, it is a...

    I have a scanner on my smart phone, it is a scanner and data base directly from GM and it WILL scan the imprinted laser box on the seal bolts. That laser imprint tells me EXACTLY who the engine was...
  24. Not only have I checked fuel, but have also...

    Not only have I checked fuel, but have also pumped crates, checked valve springs and passed a camera down through them. Not all tech is created equal. Just because it has seal bolts doesnt mean squat...
  25. Replies
    5
    Views
    1,269

    there is a very tiny hole in the bottom of the...

    there is a very tiny hole in the bottom of the MC, next to the bigger hole, it is probably plugged with dirt. This is the bleed hole for the line pressure relief. It is there so when your clutch...
Results 1 to 25 of 275
Page 1 of 11 1 2 3 4

All times are GMT -5. The time now is 06:02 PM.


Powered by vBulletin® Version 4.2.0
Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.