|
|
Search:
Type: Posts; User: 6burg
Search:
Search took 2.49 seconds.
-
I picked up some tires from Scott at Hoosier Midwest in Springfield and he said that a40s is 3 points softer than present a40 and the sprints in Florida ran the new compound and that the 1st and 2nd...
-
I talked with jeff Johnston of billet fabrication who was helpful explaining importance of drain backs with Titan pumps , he suggested after confirming that oil restrictors were installed I should...
-
No existing drains to pan
-
eng was fresh this yr just started around June and has became gradually worse, is there a prefered place in oil pan to drain into ? Going to call Titan and see about rebuild kit while pans off.
-
Oil pressure dropping below 20 psi when braking hard on sbc 421 18 degree .warning light coming on .. Goes almost to zero but comes up when raise rpms. Jeff johnston custom 10 qt pan . tried adding...
-
I moved them out as per book. While moving I was surprised at how much inch made to springs and shock travel. Especially LR . All the paint was rubbed off door cage behind driver from too much...
-
Just purchased used pierce, 2012 clamped, came with book which says measurement from rear shock mounts c/c 38 1/2 inches mine measures 36 1/2. Measurement from rotor to shock mount on each side...
-
Thanks , looks like they've been having good car counts, hope to get over there this summer
-
-
thanks appreciate all the input,
-
thats rpm's I'm looking for. Did you feel like you were hooked up pretty good?
-
thanks Travis, I've got a 6:00 ,hoping to get by without buying another gear, 7200-7500 's in my confort zone. I might give it a try at one of thier practices.
-
what gear for clay county (flora) 9in. , 7200 rpm range
-
I'm on 3rd year with mine, no problems. wouldn't hesitate to buy another set. turn 6800-7200 in 14-1 400 dart shp block
-
shop in bathalto illinois, Ron's porting did porting, performance automotive set up and assembled heads. in my opinion the problem was due to only one valve being checked and clearances being set...
-
Picked up heads from machine shop, took to another shop and disassembled and inspected . Found guides were smooth type, not spiral to help with oiling and he had button style sleeves and they were...
-
Dart platinum iron head 215 runners ported at rons porting in St. louis on cnc machine . 5/16 valve stems ,manley valves. after 20 laps #6 exhaust valve siezed in guide,tagged piston and bent. paid...
-
Pics are sent to your email.
-
It's not letting me download the pictures. I can send the pictures to your email.
-
I have a rear axle housing that came with car just bought,the upper mount on right side is mounted aprox 1 inch forward of the left upper mount. the housing I just had jigged is mounted straight in...
-
bought a set of the reinforced front segment afco's last year. they are quite a bit stiffer , which raised body height considerably. had to add 1 1/2 lowering blocks to get ride height back to spec....
-
Looked like he cut lower mounts from another frame and welded them below existing mounts. this would give some adjustability. he had single hole lowers on axle housing.
-
I basically used the method bushracing67 showed in drawing using a 12 ton bottle jack and log chain. I broke one of the new cheap 3/8 rural king chains, bolts, jack and schrapnel flying everywhere....
-
Thanks for the info , it has been hit from rear and is out 1/4 inch in front [ toed out] This gives me something to work with. I'll remove housing this week and measure more accurately and see...
-
they are diffrent lengths , measuring from the rotors pretty much tells the story, bent housing, I'm going to run it like it is . it's not off much, axle still goes in .
All times are GMT -5. The time now is 07:07 AM.
|
|