Search:

Type: Posts; User: TC65

Page 1 of 2 1 2

Search: Search took 0.77 seconds.

  1. Thread: rpm question

    by TC65
    Replies
    1
    Views
    43,809

    rpm question

    changed engine and transmission and after doing this when the engine is running and the hood is raised the RPM of engine increases about 200. when the hood is put back on it decreases 200 rpm. ...
  2. Replies
    0
    Views
    2,748

    Sway Bar spring rates

    Any one have spring rates for 1' 1 1/8 1 5/16 and 1 3/8 inch Mustang sway bars.

    Thanks
    TC65
  3. Thread: 2.3 crankshaft

    by TC65
    Replies
    4
    Views
    3,778

    2.3 crankshaft

    When should the crankshaft be changed in a 2.3 ford ? I have heard they should be changed after each year of racing. Have one that has 10 races on it. It was new last year when installed.

    TC65
  4. Replies
    2
    Views
    3,434

    Mustang front control arms

    What is the best way to remove the stock bushing in the front control arms?

    thanks
    TC65
  5. Thread: Chevy valves

    by TC65
    Replies
    1
    Views
    1,000

    Chevy valves

    Anyone use CHEVY valves in a Ford 2300 head Is there an advantage for using them?


    Thanks
    TC65
  6. Replies
    2
    Views
    1,133

    Mustang rear adjustable spring buckets

    Need help and info on installing rear adjustable spring buckets. Materials, where to buy ,etc.

    Thanks
    Tc65
  7. Replies
    3
    Views
    2,194

    belt wiggle

    Thanks Dave I will remember that
  8. Replies
    3
    Views
    2,194

    The belt was the problem. Using a Gates racing...

    The belt was the problem. Using a Gates racing belt which is about 5 years old. It had thin places like it had stretched.
    Put a new one and it runs perfect.

    Thanks

    TC65
  9. Replies
    3
    Views
    2,194

    Timing belt wiggles

    Installed new 2300 engine and the timing belt looks like it is going to run off the aux and cam pulleys when running. I have changed the belt tensioner, the cam gear and the belt still moves. The...
  10. Replies
    0
    Views
    1,353

    5 speed mustang transmission

    I am going to install a 5 speed transmission in our race car. My question is do I need to use a short clutch lever ball or a long one? We used this trans. about 5 yrs ago and think we used the long...
  11. Replies
    7
    Views
    2,992

    Light Wiseco Pistons and LIght rods. I am not...

    Light Wiseco Pistons and LIght rods. I am not sure but think the pistons are chevy
  12. Replies
    7
    Views
    2,992

    5.2 vs 5.7 Bottom End

    WE have been running a 5.2 rod bottom end for years and decided to go to a 5.7 rod bottom end. We used everthing from the old 5.2 bottom end, clutch, flywheel, etc. After running the 5.7 bottom end...
  13. Replies
    6
    Views
    2,360

    I have tried a PM and have not gotten anything,

    I have tried a PM and have not gotten anything,
  14. Replies
    6
    Views
    2,360

    Thanks Browndog, I have sent them three Emails...

    Thanks Browndog, I have sent them three Emails but have not an answer.

    TC65
  15. OLD ROB, How do you order from Powerbyace? Been...

    OLD ROB, How do you order from Powerbyace? Been trying for about 2weeks. No one will answer my Emails.

    Thanks
    TC65
  16. Replies
    6
    Views
    2,360

    Ford 2300 rocker billet studs

    I have been trying to order rocker studs and nuts from AUTOMOTIVE COMPONENT ENGINEERING. I have sent 3 Emails with the part numbers but have not received a response. Does anyone know if they are...
  17. Replies
    2
    Views
    1,649

    2300 head and intake manifold

    What is the best combination of heads and intake manifolds? Oval head/oval intake , Oval head/dport intake? Have been running oval/oval with good results. Have run oval/d port and did not see any...
  18. Replies
    19
    Views
    3,938

    I have 3 Mels distributors and have never used...

    I have 3 Mels distributors and have never used his coils. I have used the stock round and square FORD coils. At present time I am using the MSD FORD TFI blaster coils and have not had any problems....
  19. Replies
    1
    Views
    1,210

    80 Mustang front brake rotors and calipers

    Wanting to change rotors and calipers on our Mustang race car . We have been using the 9 inch stock rotors and calipers. There is alot of drag using these. Is there any aftermarket rotors and...
  20. Replies
    9
    Views
    2,159

    Remove the control arms and then measure the...

    Remove the control arms and then measure the center of one bushing to the center of the other bushing. Remove the bushings from the control arms. Weld a piece of 1/4 inch key stock inside where the...
  21. Replies
    10
    Views
    1,852

    1195 I think and hope you are right. I have a 80...

    1195 I think and hope you are right. I have a 80 Ford tech and it says to inspect this bushing when changing the seal. I have a tail shaft that is off another trans. and I removed the seal in it and...
  22. Replies
    10
    Views
    1,852

    It is leaking between the yoke and the seal. I...

    It is leaking between the yoke and the seal. I have checked yoke for scratches etc. found nothing. the yoke measures about .003 larger than the seal. The vent is open on plate. Have changed the...
  23. Replies
    10
    Views
    1,852

    German 4 speed Transmission

    Having problem with the tail shaft seal leaking in our transmission. When the car is sitting in the shop it will leak app. 2oz. when running at the track we do not see any signs of leakage. In the...
  24. Replies
    5
    Views
    1,291

    Ford 2300 Head Gaskets

    Have neen using Victor Reinz head gaskets. Have not had any problems but it takes an hour or so to clean the head and block after the head is removed. What are other choices without the cleanup?
    ...
  25. Replies
    3
    Views
    1,384

    Thanks Dave, I watched 7 videos on indexing. Four...

    Thanks Dave, I watched 7 videos on indexing. Four said index the open end of the grounding strap to the intake valve, two said index to the exhaust valve and other one said to get between the ex. and...
Results 1 to 25 of 38
Page 1 of 2 1 2

All times are GMT -5. The time now is 11:10 PM.


Powered by vBulletin® Version 4.2.0
Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.