Search:

Type: Posts; User: Jb35

Page 1 of 2 1 2

Search: Search took 0.34 seconds.

  1. Thread: 79mustang help

    by Jb35
    Replies
    2
    Views
    3,075

    What's your engine rules?

    What's your engine rules?
  2. Thread: 2.3 crankshaft

    by Jb35
    Replies
    4
    Views
    3,776

    The best time to change a crank is after it...

    The best time to change a crank is after it starts to crack but before it breaks. lol. I inspect crankshafts after every season. The engine I run has 65 races on the crank over the course of 3...
  3. Replies
    2
    Views
    1,031

    Make sure cam pulley belt quide is on and turned...

    Make sure cam pulley belt quide is on and turned the right way. Make sure belt isn't too tight. I've never run shims on the aux pulley before. Make sure all pulleys match as far as square tooth or...
  4. Thread: Shim oil pump

    by Jb35
    Replies
    6
    Views
    1,267

    I don't think you would want a washer between oil...

    I don't think you would want a washer between oil pump and pickup. However there is a spring inside the pump that a lot of people,including myself, use a washer to shim up and add more pressure. An...
  5. Thread: Msd rev limiters

    by Jb35
    Replies
    2
    Views
    1,324

    That's interesting. They use to check our rpms...

    That's interesting. They use to check our rpms when I ran gokarts. The track I race at rpm changes night to night usually by 2 or 300 rpms depending on track condition and weather.
  6. Thread: ratio chart?

    by Jb35
    Replies
    10
    Views
    3,666

    Put transmission in gear mark input shaft and...

    Put transmission in gear mark input shaft and output shaft. turn input shaft 10 rounds count how many times output shaft turns. divide 10 by output shaft rotation. You now have your transmission...
  7. Thread: running hot

    by Jb35
    Replies
    10
    Views
    2,410

    7uptruckracer. Double pass is on now. Not arguing...

    7uptruckracer. Double pass is on now. Not arguing with you, but y not triple pass just out of curosity.
  8. Thread: running hot

    by Jb35
    Replies
    10
    Views
    2,410

    I'm going to try to jet it up some but I don't...

    I'm going to try to jet it up some but I don't think it's lean. Running 350 holley, 72 jets. Carb built by competition carbs. Turning motor 82 to 8300 rpms. Plugs look good. 36 degrees advance timing...
  9. Thread: running hot

    by Jb35
    Replies
    10
    Views
    2,410

    running hot

    I race asphalt ford 2300. I have an issue of running hot and i can't seem to keep this thing cool. As long as were under green conditions temp just keeps climbing until we get a caution then it will...
  10. Replies
    10
    Views
    3,550

    Ask cam manufacturer. But I'm going to guess and...

    Ask cam manufacturer. But I'm going to guess and say 110 to 120 at seat 240 to 260 open.
  11. Thread: Camshaft question

    by Jb35
    Replies
    1
    Views
    1,027

    Holman moody cam. .454 lift. Specs are on their...

    Holman moody cam. .454 lift. Specs are on their website.
  12. Replies
    19
    Views
    3,938

    Im thinking if you have 2 12 volt batteries wired...

    Im thinking if you have 2 12 volt batteries wired in series thats 24 volts. You would want them wired parallel. Correct me if im wrong.
  13. Replies
    9
    Views
    2,159

    Im interested in hearing some opinions on this....

    Im interested in hearing some opinions on this. It be easy enough to do but seems like a crutch for improper 4 link geometry.
  14. Replies
    5
    Views
    1,165

    Run the little original breather dnt run a hose...

    Run the little original breather dnt run a hose or anything. It will work just fine and if it blows a little oil u will nvr no it.
  15. Thread: Cam problem

    by Jb35
    Replies
    14
    Views
    1,842

    My opinion if at all possible learn to do that...

    My opinion if at all possible learn to do that kinda work yourself. It requires very little special tooling, you will save money in the long run, and u will be more exact on ur stuff then someone...
  16. Thread: Cam problem

    by Jb35
    Replies
    14
    Views
    1,842

    Geometry isnt correct one follower shows too much...

    Geometry isnt correct one follower shows too much lift another shows too little. Hard to tell from pic but if there are grooves wore in followers spring pressure is off too.
  17. Thread: Cam problem

    by Jb35
    Replies
    14
    Views
    1,842

    Call both builders and call lunati. If they are...

    Call both builders and call lunati. If they are good experienced builders, not saying they arn't, they should be able to tell u what went wrong.
  18. Thread: Cam problem

    by Jb35
    Replies
    14
    Views
    1,842

    I havn't run that cam, but lunatis are usually...

    I havn't run that cam, but lunatis are usually pretty good cams. Are you breaking the cam in correctly?
  19. Replies
    4
    Views
    1,120

    320 could be the cam lift. .320 cam lift with a...

    320 could be the cam lift. .320 cam lift with a 1.6 rocker ratio will yield about .510 total valve lift.
  20. Thread: Break up

    by Jb35
    Replies
    5
    Views
    1,689

    I use the 84 ranger fuel pump as well. Thats a...

    I use the 84 ranger fuel pump as well. Thats a lot of power valve I run a 7448 carb with a 3.5 power valve. Then depending on cam anywhere from 68 to 74 jets usually.
  21. Replies
    8
    Views
    1,717

    So far good results with needhp's rockers. 275...

    So far good results with needhp's rockers. 275 lbs open pressure on valve springs turning 8200 rpms.
  22. Replies
    2
    Views
    1,052

    Yes you can run a quickner without power steering...

    Yes you can run a quickner without power steering just make sure nothing binds in the steering linkages. I used to run one.
  23. Replies
    8
    Views
    1,717

    I'll buy some padded followers new or used if any...

    I'll buy some padded followers new or used if any one has any to sell. If there in decent condition. Just private message me.
  24. Thread: steering

    by Jb35
    Replies
    1
    Views
    845

    It shouldnt be to bad. It is a little tighter but...

    It shouldnt be to bad. It is a little tighter but it should b manageable.
  25. Replies
    3
    Views
    1,291

    Those pics are representative images not the...

    Those pics are representative images not the actual part. The part wont have the "wings" but my advice go to advance or oreillys and then you can see it before u buy it.
Results 1 to 25 of 37
Page 1 of 2 1 2

All times are GMT -5. The time now is 09:09 PM.


Powered by vBulletin® Version 4.2.0
Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.