Search:

Dirt on Dirt. UBoB @ Brownstown: Feature

I believe the car Barnett was in was a Rayburn. The halo was bent down a substantial amount, from what I was told by multiple people who saw it. From the series of impacts directly on top of the...

Your assumption is correct, at least that is how it has been in the past. Basically there are 3 times as many cars as what the pits will hold, so there are more cars in the spectator parking and...

I think the tape or plastic for sun/light glare is needed more now that the halo and roof of the cars are 4+ inches higher than they used to be. I never used any tape on the windshield bars on my old...

I am 6'3" had an older Masters, tight fit. It was about 36" floor to cage. Some 2009 and all (I think)2010 and newer MasterSbilt are around 38". That made a huge difference for me. In the last few...

Steve Francis did in the 2003 to 2006 range, Ray Cook around that time or a little later. EPJ was the last one I remember running one "nationally", and that has been at least 5 years ago? My years...

The way I understood his comment was using a mono-leaf or "half leaf" or some type of flexible / spring steel material in place or the LRU link rod, if a rule was put in place to make the spring...

That would also be west.

That would be west on 50. Then south on 135. The name is Hickory Hills. Otter Creek in Columbus is about 45 minutes, that would be as good as anything under an hour.

Raise the motor 1".

Brownstown Speedway is 1 hour south of Indy. March 14th opening night, March 21st Lucas Oil.

I'm not 100% sure, but I thought the Wissota cars had more engine set-back. I guess it could be that they are a longer wheel base and the mid-plate is the same distance from the rear axle, thus...

I will leave it to Matt49 or MasterSbilt_racer to help you with a complete set-up, as I am certainly no expert. But I will say from my experience with the same car as yours that your biggest problem...

The module is bad, no question about it.

My 2010 Smack had the limiter chain mount behind the battery box and on the outside of the frame rail. The mount was angled so that it pointed at the center line of the axle when the LR was at full...

http://www.speedwaymotors.com/Dominator-Late-Model-Dirt-Nose-Graphics,35982.html

Dominator makes them, unless you are wanting a different model or something.

The GRT lift bar had 4 mounting points: The 2 studs on the right side bell that are normally used and the 2 adjacent studs on the left side bell. Of course it did not use a support bar off of the...

Owner is ready to sell, don't be afraid to make an offer. (No Trades) This car is ready to race minus body.

Motivated seller, open to reasonable offers. Also have some spares including tires, wheels, springs, gears, etc. that could be included for the right price.

Motivated seller, open to reasonable offers. Also have some spares including tires, wheels, springs, gears, etc. that could be included for the right price.

http://www.racingjunk.com/Late-Models/182114988/2010-MasterSbilt-Smackdown-604-Turn-Key.html

http://www.racingjunk.com/Late-Models/182114988/2010-MasterSbilt-Smackdown-604-Turn-Key.html

Brinn 34" - 34.5", standard Bert 36" - 36.5" for a 2010 Smack. I would assume that a 2008 would be the same.

My 2010 Smack has everything raised. I thought that the raised right side frame rail started on a few late 2006 models and they all had it by 2007, but I will not dispute the above post since I...

http://www.4m.net/showthread.php?271053-Bedding-down-for-the-winter