Search:

Type: Posts; User: 3dracer

Page 1 of 4 1 2 3 4

Search: Search took 1.04 seconds.

  1. Replies
    2
    Views
    872

    For us in UMP land, they check the lowest point...

    For us in UMP land, they check the lowest point on top, which generally is the halo, to the highest point on the decking. The main parts that you must be able to squeeze by on exit.
  2. Replies
    3
    Views
    1,316

    It will somewhat limit travel. But that is about...

    It will somewhat limit travel. But that is about all that I can think of.
  3. PEM 9" Rear Gears for sale - XTreme Light and REM finish

    I have several sets of 9" gears for sale. These are fully optioned by PEM and in their cases with short wide yoke on it. REM finishing throughout and Xtreme lightened. These are not cheap gears...
  4. Replies
    3
    Views
    653

    A lot less. About an inch either direction.

    A lot less. About an inch either direction.
  5. Replies
    3
    Views
    2,264

    I was just at Butler Motor Speedway last weekend...

    I was just at Butler Motor Speedway last weekend to watch.
  6. Replies
    15
    Views
    2,023

    What would more pinion angle do for the car if it...

    What would more pinion angle do for the car if it really doesn't lose much on acceleration? You can test all of this in the shop. I run just enough to keep it the same as the transmission angle...
  7. Replies
    25
    Views
    5,846

    Impressive measures from the top of the lower a...

    Impressive measures from the top of the lower a arm to a hole in the frame. That is why his appears to be low. But I think 100 lbs lr is too much. Almost sounds like a jbar push on entry. ...
  8. Replies
    35
    Views
    6,402

    Mine is mounted right beside the driver on the...

    Mine is mounted right beside the driver on the other side of the interior. I ran the nozzles to the appropriate spots then. I have a bar that runs from the dash bar to the bar right behind the seat...
  9. Replies
    4
    Views
    1,697

    This is handy ...

    This is handy


    http://staffordmotorspeedway.com/wp-content/uploads/GM-602-CRATE-ENGINE-TECH-MANUAL.pdf
  10. Replies
    4
    Views
    2,888

    Depends on the roll out of the tires. But start...

    Depends on the roll out of the tires. But start with the control arms in the front level. Measure the bolt to the ground and then measure the center of the ball on the ball joint to the ground. ...
  11. Replies
    12
    Views
    3,349

    Where did you see them at? I can't find them.

    Where did you see them at? I can't find them.
  12. Replies
    15
    Views
    3,237

    We ran it for several seasons. I liked it a lot...

    We ran it for several seasons. I liked it a lot because of price. The local stations are not very accurate around me so we ended up mixing it ourselves. We bought e98 and mixed it with gas to get our...
  13. Thread: AMC Spindle

    by 3dracer
    Replies
    4
    Views
    2,974

    More than you think. I do not, but I have seen a...

    More than you think. I do not, but I have seen a couple.
  14. Replies
    5
    Views
    1,550

    If your tech man looks around these, I would race...

    If your tech man looks around these, I would race at another track.
  15. Thread: Brake help

    by 3dracer
    Replies
    5
    Views
    1,476

    Thanks everyone. We will take a look at all. We...

    Thanks everyone. We will take a look at all. We are running the preload spacers on all 4 corners. It might be causing a little hub shake.
  16. Thread: Brake help

    by 3dracer
    Replies
    5
    Views
    1,476

    Brake help

    Embarrassed. Brake question I cannot figure out on my own. All new stuff on a new modified chassis. Afco pedals, steel brake lines, Afco calipers, Afco high temp brake fluid, Afco brake pads,...
  17. Replies
    10
    Views
    2,774

    Well. My program got the same numbers as above. ...

    Well. My program got the same numbers as above. But with that said, there are a lot of variables that go with that. Kudos to Verdoorn.
  18. Replies
    10
    Views
    2,774

    Just now remembered to look back at this thread. ...

    Just now remembered to look back at this thread. I apologize. I will try to get it done this evening.
  19. Replies
    6
    Views
    2,497

    That is normal for them. At least from my...

    That is normal for them. At least from my experience.
  20. Replies
    10
    Views
    2,774

    I can do this for you. I have the R&D program...

    I can do this for you. I have the R&D program that will tell me. I just need to know what you want for weight and percentages.
  21. 395 steel head Street Stock/Sportsman engine

    My race car friends. If you are needing an engine. Think back a few years when you all got out-run by the 3D car... A PERFECT street stock class engine or even a good modified with steel heads.
    We...
  22. Replies
    2
    Views
    1,745

    I agree. But even if you dont know what you want....

    I agree. But even if you dont know what you want. It will tell you if you make a change, what will happen static and dynamic.
  23. Replies
    113
    Views
    20,965

    It had IMCA seals too

    It had IMCA seals too
  24. That is real close to an IMCA modified. No place...

    That is real close to an IMCA modified. No place for a bmod.
  25. Replies
    6
    Views
    4,086

    Been done for several years. All it really does...

    Been done for several years. All it really does is tighten up the center.
Results 1 to 25 of 91
Page 1 of 4 1 2 3 4

All times are GMT -5. The time now is 06:19 PM.


Powered by vBulletin® Version 4.2.0
Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.