Search:

Type: Posts; User: JustAddDirt

Page 1 of 20 1 2 3 4

Search: Search took 3.98 seconds.

  1. Replies
    9
    Views
    913

    If I was to go crate racing, I would definitely...

    If I was to go crate racing, I would definitely go with e85. Temps run cooler,
    Little more snappy on power. I know itís a bit more work with testing fuel, and all, but it beats Worrying about...
  2. Replies
    9
    Views
    913

    throw the 3 blade jones in trash, get a 4 blade...

    throw the 3 blade jones in trash,
    get a 4 blade GM or a race blade 3-4 blade setup
    does your serpentine system have the idler tensioner wheel on it?
    what water pump do you have on it?
    Stewert...
  3. put 68-72 nova lower a arms on it and it will...

    put 68-72 nova lower a arms on it and it will help widen out suspension
  4. Replies
    6
    Views
    540

    drill a hole at the end of the crack to stop it....

    drill a hole at the end of the crack to stop it.
    then die grind down the center of the crack on both sides, and have a good aluminum welder weld it.
  5. Replies
    10
    Views
    3,555

    wander if Hud is rethinking his decision of the...

    wander if Hud is rethinking his decision of the MasterSbilt deal?
  6. If I remember right they were Ford oil pump gear...

    If I remember right they were Ford oil pump gear set, possibly remachined. I think big block ford, but I am u sure which version. I would assume 429 or 460, but could be FE style that was Most...
  7. Replies
    10
    Views
    905

    bumper

    yes it will. may need to weld on a new spud on RF to accept it.
    little bit different in width, but not much
    Blue/grey bumper comes straight out from chassis on right side
    Masters bumper has a bend...
  8. Replies
    28
    Views
    3,283

    also run a stiffing bar from the LF upper coil...

    also run a stiffing bar from the LF upper coil over area on downtube, back to the door bar area. stiffens quite a bit as well.
  9. Replies
    5
    Views
    1,057

    Not sure what years and models, but I would...

    Not sure what years and models, but I would assume starting around 2000 model years 2500 and 3500 4x4's
    My 09 2500HD Duramax has one that looks like the 700 series.
  10. Replies
    5
    Views
    1,057

    box

    depends on how fast you want it
    the shorter the steering arm on spindle is say Mustang II most do an 8:1
    if using a GM Metric length arm most do the 6:1
    arm length on steering box and idler arm...
  11. Replies
    10
    Views
    905

    wider than the max track width in rulebook.

    wider than the max track width in rulebook.
  12. agree. you need to go to a big bore short stroke...

    agree. you need to go to a big bore short stroke to get what you are wanting.
    4.125-ish bore.
    3.5-3.625 stroke
  13. Replies
    5
    Views
    1,057

    700 series saginaw boxes are 3-5 pounds lighter...

    700 series saginaw boxes are 3-5 pounds lighter than the 600 series Saginaw boxes. but all the aftermarket companies I would assume are using a stock GM box, just rebuilding it with new guts and new...
  14. Replies
    16
    Views
    1,491

    Dirtslinger20 are you using an automotive style...

    Dirtslinger20
    are you using an automotive style exhaust hanger?
    I personally like a hanger from an auto parts store that has a block of rubber in it, and a j hook that you can hose clamp the to the...
  15. Replies
    19
    Views
    3,435

    roof

    If it is the air diffusers that you are looking at on the back of the roof those have been molded into the composite roofs for a long time.
  16. Replies
    5
    Views
    428

    needs to be 1/2" below fill plug or site glass....

    needs to be 1/2" below fill plug or site glass.
    believe you have to much fluid in it.
  17. Replies
    5
    Views
    428

    how much fluid are you using to fill? IIRC it is...

    how much fluid are you using to fill?
    IIRC it is like 3/4 of a quart.
    also do you have the vent tube running vertical, then a loop at the top and running back down?
  18. Thread: RF Setup

    by JustAddDirt
    Replies
    25
    Views
    3,650

    Sounds like an xr1 with those travel Numbers

    Sounds like an xr1 with those travel Numbers
  19. Replies
    3
    Views
    451

    tilted carb spacer lower float levels tilt...

    tilted carb spacer
    lower float levels
    tilt motor down in back, and lean motor to left.
    connect the 2 vent tubes with a piece of clear tubing, and make a hole in the top to vent them.
  20. Replies
    3
    Views
    532

    need to upgrade the rear end. I don't believe...

    need to upgrade the rear end. I don't believe those 7.5 axles are not strong enough for oval track racing.
    JMO
    if you try it, make sure you do the c-clip eliminators on the axles . that is the...
  21. ***398 CI UMP modified motor for sale***

    Built by Williams Precision Engines in St. Paul Indiana at beginning of 2019 season
    ran 7-8 races
    Dart Little M block 1.185 bore
    Brodix full CNC 18ļ heads (new mid 16) (new valves springs locks...
  22. I have been into the Gen2 Bert's. They are...

    I have been into the Gen2 Bert's.
    They are pretty easy to service
    Just make sure the black thrust pads stay in place
  23. Thread: LR Index

    by JustAddDirt
    Replies
    17
    Views
    1,949

    bar-ed up literally

    I have often thought of doing a solid rod on the LR and RF, and trying to test it, or at least a solid rod on LR. Never had the balls to try it though.
  24. Replies
    20
    Views
    1,510

    View Post

    I would agree, the 2nd gen Bert doesnít have a lot rotating in high gear. Virtually straight shot threw. Has just enough turning to splash lube bearings.
  25. Replies
    1
    Views
    520

    Sold.... thank you 4m

    Sold.... thank you 4m
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

All times are GMT -5. The time now is 12:10 AM.


Powered by vBulletin® Version 4.2.0
Copyright © 2020 vBulletin Solutions, Inc. All rights reserved.