|
|
Search:
Type: Posts; User: Mad Jack
Search:
Search took 3.34 seconds.
-
That was a very good Deal. Congrats on the sale.
-
For the Aluminum Tail Housing With the Rear Seal and Bushing in it already part # 72024 Might also want to check the 74010 Output Shaft for straightness??
-
What Transmission is it, 70001Aluminum - 70010 Magnesium 70600 New Predator 70501 Proseries
-
Possible Drive Shaft, Or Transmission Output Shaft?
-
Its just a rubber hose with fittings that can be fastened up higher in the tunnel for the guys that are blowing fluid out the breather.
-
Brett4, Have you noticed any vibrations?? When you get a chance send them into Brinn to be checked out.. Or even one at a time to have them looked at.
-
Are these New Transmissions ? Has the rear seal and bushing been replaced? Just trying to get more info on these trans. There is also a Serial # stamped in the top of the main case and the top of the...
-
Bert has the Gen 2 @ 36.9 Lbs. the are about 2 inches shorter than the Brinn along with the internal parts are different.
-
RCT, It depends on how old your transmission is..? 70001 Trans Serial # 3858 or higher you could use a 8" if you want If the number is lower you will have to get a different 74010 Output Shaft to...
-
Very nice and time consuming but that you for posting the link to the cars that was there. Did not make it down there this year.
-
You could try contacting Kevin Sloan, Not sure if he is still racing his Modified or not but I know he has a setup like you are looking for?? He raced at Lake Side Speedway and is on you tube....
-
I wish I had or had a lot better sponsors to help get this I think it would be a good starter car I only say that for a couple reasons 1 being I would like to try moving up for next year, and 2 being...
-
Yes sir I do just trying to give Tech Support to help out if I can or when I can I am not pushing our products I do not know everything I actually have learned some things from being on here.
-
Yes that is another good point, Make sure the Bell Housing is clean and also the starter face where the Starter bolts to Bell Housing, And Gage of wire also Like if your running up to 7 foot should...
-
I would recommend like stated above just a graphite or light white grease, Keep it clean, And the Brinn should be between .040-.070 between the idler gear and flywheel with the starter bolted in.
-
Here is what you are looking for. TAP DRILL THRU, 1/8-27 NPT
-
Have you tried call Lou Fegers Racing @ (800) 328-3618 Part number should be 71018 Or Rapid Performance Sauk Rapids, Minnesota 56379 (320) 253-1069
-
I sent a guy on 1/26 to you hope it works out for the sale for you
-
Is there anything wrong with it?? Just wondering why selling with only one night on it.?? Has it been updated yet.
-
As stated above here as long as you are using the Brinn Flywheel with the Brinn Bell Housing you should be all set. Just do not use a Bert Flywheel with a Brinn Bell Housing. The Transmissions should...
-
I think the Brinn Clutch also has the teeth heat treated and are about .081 Thick. Hope it helps.
-
Plus make sure you are using the same brand Flywheel as the Bell Housing they do not enter change very well and going to ruin flywheel.
-
What yoke are you using? make sure the O.D is like 1.500 - 1.502 Max. Might be a burr in the bushing area. Make sure there is a little play at the top of the pedal and that should ensure the Piston...
-
No they are different also Bert is Bert and Brinn is Brinn
-
No the Berts are thicker than the Brinn and you will not get the correct stack up if you mix match these.
All times are GMT -5. The time now is 08:19 PM.
|
|