Search Results - 4m.net - The Most Opinionated Racing Message Board In The Universe




















Search:

Type: Posts; User: 72Dubya

Page 1 of 18 1 2 3 4

Search: Search took 0.09 seconds.

  1. Replies
    10
    Views
    323

    Do you have any examples of front running cars...

    Do you have any examples of front running cars running soft tires on a rubbered up track? Because I was at a practice day and the track was rubbered up and I thought that that I could run a soft tire...
  2. Replies
    21
    Views
    1,561

    Here's my issue with the B-Mod rule conundrum: We...

    Here's my issue with the B-Mod rule conundrum: We have a good modified chassis sitting in the shed, ready to be a B-Mod, just needing a motor and to swap the rearend, which we have, but we are not...
  3. Replies
    5
    Views
    616

    What is your LS percentage?

    What is your LS percentage?
  4. Replies
    16
    Views
    2,100

    There have always been claims of TC in the champs...

    There have always been claims of TC in the champs car every year for as long as I can remember. I remember earlier in the year someone said all the top 5 had TC.

    Just jealous people trying to...
  5. Replies
    70
    Views
    8,489

    Rumor has it that they are going to put out a one...

    Rumor has it that they are going to put out a one compound tire rule with a compound similar to the LM30 tire. I hope this is true. The loss of the spoiler in combo with a harder tire will definitely...
  6. Replies
    5
    Views
    805

    Free up the car.

    Free up the car.
  7. Thread: Need Help

    by 72Dubya
    Replies
    6
    Views
    1,200

    Making a car a front runner takes more than...

    Making a car a front runner takes more than tricks and parts. It takes setup and driving ability as well.

    Start out with beginning to correct your front end geometry and then go from there. This...
  8. Replies
    5
    Views
    836

    That could be it. You do not want the tire to...

    That could be it. You do not want the tire to roll over on the sidewall past the dot in the i in the Hoosier painted on the side.
  9. Replies
    8
    Views
    1,030

    Well, I used some of the above mentioned tips and...

    Well, I used some of the above mentioned tips and techniques this weekend, and it went well. If the track wasn't one lane on the high side in the heat I could have passed the leader and walked away...
  10. Replies
    5
    Views
    836

    On a 3200 lb SS, you do not want to go any lower...

    On a 3200 lb SS, you do not want to go any lower than 18 psi on the right side.
  11. Replies
    8
    Views
    1,030

    The car isn't tight, it does what it needs too. I...

    The car isn't tight, it does what it needs too. I run rear brake on tacky tracks, I just do not feel that as the driver I am doing things correctly, like corner entry. I am a driver that likes the...
  12. I am going to predict that about post #15 it will...

    I am going to predict that about post #15 it will become a usual 4M pissing match lol
  13. Replies
    8
    Views
    1,030

    Heavy/Tacky track driving

    What are some main things to do while driving when racing on a tacky track. This is kind of backwards because if the track slicks off or gets dry/black I am fine, always up front in contention, but I...
  14. Replies
    2
    Views
    717

    x2 on the American Racer.

    x2 on the American Racer.
  15. Thread: Need Help

    by 72Dubya
    Replies
    6
    Views
    1,200

    Correct the anti-dive on the upper control arms...

    Correct the anti-dive on the upper control arms for starters. Just drill a new front mounting hole to drop the front of the control arm level with the rear. This is something simple though.

    There...
  16. Replies
    4
    Views
    711

    A local parts store can get your basics (tie...

    A local parts store can get your basics (tie rods, drag link, balljoints, pitman arms, idler arms, steering box, bushings, etc..) . Spindles and stock upper and lower control arms you can find either...
  17. Thread: tire questions

    by 72Dubya
    Replies
    6
    Views
    1,180

    The tire wasn't hooking up. If it was your LR I...

    The tire wasn't hooking up. If it was your LR I would assume the RR was not as hot but showed wear.
  18. ohiovalley- Here is the GRT roller price. It...

    ohiovalley- Here is the GRT roller price. It shows prices of all the parts to help break down where the cost comes from. ($15,700)
    ...
  19. Replies
    37
    Views
    3,202

    I am running an all steel flat tappet 374 with a...

    I am running an all steel flat tappet 374 with a two barrel, and on the dyno (engine and chassis both) from 3000 rpm up to when the power drops off, the torque and HP curves were close to identical....
  20. Replies
    6
    Views
    1,155

    Yes in some cases there can be an advantage. Some...

    Yes in some cases there can be an advantage. Some 8 inch tires, especially the E-MOD series, actually have a 9 inch tread width (ask the guys at Hoosier and they can confirm this), and I have seen...
  21. Thread: steering help

    by 72Dubya
    Replies
    4
    Views
    1,450

    The 6:1 Sweet box is good if you are a driver...

    The 6:1 Sweet box is good if you are a driver with deep pockets (pricey, but great quality) and that likes to feel the track more with your frontend (eliminates quickener and gives you "almost"...
  22. Replies
    7
    Views
    1,636

    Honestly, I do not really like the whole Nova...

    Honestly, I do not really like the whole Nova deal. I am on all stock metric components, except we can run racing shocks with after market mounts and correct our uppers, and I am very competitive...
  23. Replies
    7
    Views
    1,636

    Usually guys use Nova lowers instead of a Camaro...

    Usually guys use Nova lowers instead of a Camaro lower. Close to same effect, just not quite as much work. I believe you also put them on backwards, i.e, right one on left front, left one on right...
  24. Replies
    3
    Views
    937

    Looks like a Tilton 4000 series. A few years old...

    Looks like a Tilton 4000 series. A few years old though because I don't think they put that emblem on their products anymore, but that is the older Tilton Engineeering emblem.
  25. Replies
    5
    Views
    1,262

    My vote would be no. The pinto spindle isn't as...

    My vote would be no. The pinto spindle isn't as tall and that could change upper arm angles in a bad way. The Camaro front-end is already pretty decent out of the box.
Results 1 to 25 of 439
Page 1 of 18 1 2 3 4

All times are GMT -5. The time now is 04:42 AM.


Powered by vBulletin® Version 4.2.0
Copyright © 2014 vBulletin Solutions, Inc. All rights reserved.