Search:
Type: Posts; User: Dirt Knife
Search:
Search took 1.24 seconds.
-
Run a pair of 800's across front try that
Or what do you have for stagger
-
ok
the pinion angle worked
yet when I throw it in hard and stand on it the right side frame molds the door to it
and the track.
compression on right side shocks 4-4.5" with a 700# RF and 200#...
-
http://www.thedirtforum.com/dirt/suspension/csetup.jpg
This is what I use?
-
http://www.stockcarracing.com/techarticles/scrp_0802_dirt_car_aerodynamics/viewall.html
It isn't the 600$ each magic carpet ride shocks or the flux capacitor 20+ k motor that only high $$$
teams...
-
http://www.circletrack.com/ultimateracing/ctrp_0908_aerodynamics_in_race_cars_explained/
-
-
https://www.rbracing-rsr.com/compstaticcalc.html
-
What would the effect be running Fast Boys Leaf with RR coil over behind locked to axel tube.
The Mono leaf is floated.
A lighter mono leaf say a 37# with a stiffer say 175-200# coil
Or a 68#...
-
http://www.r2cperformance.com/track-control-carburetor-spacers.aspx
-
What starting pinion angle on a fast boys
Leaf mod ??? Also. Front springs for impala
Stub. ???
Thanks. For help.
-
cleaned out my p / m inbox
thanks
-
Fastboys leaf set up front springs?
3 wheeling what sprung do you run in
Rf and LF
Softer rf to keep the push out? LF heavy
For the landing going in ???
Thanks.
-
-
Dose anyone run a thermostat in there Methanol engine?
Last season had trouble getting up to temp 140 - 150* after feature.
No shroud fan is 1.5" away can pull the spacer out to 3" away.
Would...
-
depends on pulley DIA
speedway is 30.625" have seen up to 42"
-
McMastr Carr sells
Cast Urathane 2 part mix relocate your pivot steels where you want.
durometer 80-120 ect.
-
This would be a +
A higher front roll center for a higher front weight mass. +
More antisquat in the lower links is a +
-
Right or Wrong
I run mine 1.5" ahead It has 2.5" to 3" travel.
I start at 22.5* down and as it pulls thru its arc ( as it pivots about the axel centerline in the side view) it looses its angle ...
-
Chassis Flex
Try Urethane motor mounts and trans mount.
It's better to get thru the night than blow it up.
I know you can run up front and know it's not just Sags you have blown up.
There...
-
http://www.mcmaster.com/#liquid-urethane/=mv1u80
I just make my own
drill them out the old stock ones
and save the steel insert.
Then make my own.
-
What happens to the front roll center location if everything else remains the same?
by going to a pinto spindle vs. impala spindle?
thanks
-
Your cross weight is a function of your front pecentage.
http://www.circletrack.com/featuredvehicles/ctrp_0706_weight_distribution_transfer/photo_10.html
-
run '0' stagger
Leave your cross weight alone
-
By moving your panhard bar to the front of the pinion
going into the corner it is now falling
last year it was behind the rear end rising going in
so for a tight condition going in I would...
-
What are your front end settings?
bottoming out
are you running stiffer LF than RF spring like 750 LF and 700RF
maybe your front shocks are too heavy for your springs?
Try a pair of 5's up front...
All times are GMT -5. The time now is 05:29 AM.