Search:

Type: Posts; User: Dan Clarke

Search: Search took 0.32 seconds.

  1. Replies
    14
    Views
    4,105

    Hi,I realize this is an old thread but I'd like...

    Hi,I realize this is an old thread but I'd like to know the pin height above the bottom of the lower ball joint hole. Thanks, Dan
  2. Replies
    7
    Views
    1,973

    Exactly what I was looking...

    Exactly what I was looking for................Thanks for the links..............Dan
  3. Replies
    7
    Views
    1,973

    I can't find where GM lists the specs of their...

    I can't find where GM lists the specs of their crate engine internals................Can someone direct me to a website please?.............Thanks,Dan
  4. Replies
    9
    Views
    1,822

    I went looking and found this picture but on a...

    I went looking and found this picture but on a site with Asian text, can't read what they are saying about it.............Dan
  5. Replies
    7
    Views
    1,973

    they do...........I'm not going to buy a crate...

    they do...........I'm not going to buy a crate because I prefer to build my own engines,,,................Just trying to get a feel for how exotic I need to be in parts selection for a 2-barrel iron...
  6. Replies
    7
    Views
    1,973

    Also, my rules say crates must run a 6600 RPM...

    Also, my rules say crates must run a 6600 RPM chip..........................Would a 602 hold up running up to 6600 every lap?....................Thanks,Dan
  7. Replies
    9
    Views
    1,822

    That's what I have in...

    That's what I have in mind......................... If it's...
  8. Replies
    7
    Views
    1,973

    thanks for getting back..........By "steel" do...

    thanks for getting back..........By "steel" do you mean forged?...............Thanks,,Dan
  9. Replies
    7
    Views
    1,973

    crate engine guts?

    Hi,............do the 602 and 604 grate motors use cast cranks?.................Pressed metal rods?....................non-forged pistons?...................Thanks,Dan
  10. Replies
    9
    Views
    1,822

    You're right. Direct to the pump, no rear...

    You're right. Direct to the pump, no rear pump................Instructions I got on adjusting the low gear band was to torque it to 70 ft.lbs., then back off 4 turns.................I'm thinking if I...
  11. Replies
    9
    Views
    1,822

    powerglide push start

    Anybody know about powerglides?.....I want to make a push start mechanism for my powerglide but not hydraulic, i want something manual......I think I can use parts from a motorcycle clutch release...
  12. Replies
    0
    Views
    598

    Machine shop in Tucson?

    Hi, I'll be building an LT1 circle track motor soon and am new to Tucson so am asking for recomendations as to a good race engine oriented machine shop in Tucson. Feel free to pm me at...
  13. Thread: lost forum

    by Dan Clarke
    Replies
    2
    Views
    946

    How the heck do I shape a post to have...

    How the heck do I shape a post to have paragraphs?I type it in several paragraphs but it publishes as a string.Dan
  14. Thread: lost forum

    by Dan Clarke
    Replies
    2
    Views
    946

    Guess not.Can anyone suggest a forum that is...

    Guess not.Can anyone suggest a forum that is focused on asphalt modified chassis setup?Thanks,Dan
  15. Thread: lost forum

    by Dan Clarke
    Replies
    2
    Views
    946

    lost forum

    Hi,Someone here might be able to help me.I was following an asphalt modified forum at the RacingWest.com site and the whole website dis-appeared.Anyone know where it went?Thanks, Dan
  16. Replies
    5
    Views
    1,907

    I'm going to set it up for 2" offset and elongate...

    I'm going to set it up for 2" offset and elongate the mounting brackets so I can move it a little either way if I want to later.Thanks to all,Dan
  17. Replies
    5
    Views
    1,907

    Just spent some time with the new rules, the only...

    Just spent some time with the new rules, the only engine location rule I can find is 6' forward of the rear axle. I'll see if I can get ahold of Chas Howe for starters.Thanks,Dan
  18. Replies
    5
    Views
    1,907

    Engine offset

    Hi,New guy here, building an asphalt modified and have no experience with them. Depending on engine, the rules state between 56% and 58% left weight. How much, if any, of the weight offset needs to...
Results 1 to 18 of 18

All times are GMT -5. The time now is 11:11 AM.


Powered by vBulletin® Version 4.2.0
Copyright © 2022 vBulletin Solutions, Inc. All rights reserved.