Search Results - 4m.net - The Most Opinionated Racing Message Board In The Universe




















Search:

Type: Posts; User: outlawstreet21

Page 1 of 2 1 2

Search: Search took 0.04 seconds.

  1. Replies
    6
    Views
    514

    I used a set of Ford Thunderbird Turbo front...

    I used a set of Ford Thunderbird Turbo front rotors. Bought a set of metric weld-on brackets and metric calipers. You will need to trim out the brackets where they weld to the axle just a little....
  2. Always ran the front 2 inches wider than the...

    Always ran the front 2 inches wider than the rear. With my current Camaro on a fastboys setup I run 3" all the way around.
  3. Replies
    15
    Views
    3,514

    This is my 82 Camaro. ...

    This is my 82 Camaro.

    http://www.4m.net/attachment.php?attachmentid=46231&stc=1&d=1375568976
  4. Replies
    14
    Views
    2,174

    Check out Total Custom Carbs from Louisiana. I...

    Check out Total Custom Carbs from Louisiana. I know Keith white and a lot of Imca guys use them.
  5. Replies
    1
    Views
    265

    Swelling radiator hoses

    Ok, pulled the hood to check over things before the race and the upper and lower hose was swelled to about 4" in diameter. First thought was blown head gasket. Opened radiator cap, spewed water and...
  6. Replies
    3
    Views
    367

    I don't know how much the difference is between a...

    I don't know how much the difference is between a escort and a thunderbird rotor is but I used a metric bracket and caliper and it works great. I just trimmed a little off the bottom of the bracket...
  7. Replies
    7
    Views
    983

    I have mine around 37 right now.

    I have mine around 37 right now.
  8. Replies
    7
    Views
    983

    You will need to trail the right rear 1". Have at...

    You will need to trail the right rear 1". Have at least 4" of stagger and a low cross percentage or it will push like a dump truck on the gas.
  9. Replies
    3
    Views
    575

    I found one locally a couple weeks ago. Thanks...

    I found one locally a couple weeks ago. Thanks for the reply.
  10. Replies
    5
    Views
    744

    I did a 7.5 rear disk brake conversion last year....

    I did a 7.5 rear disk brake conversion last year. Used thunderbird rotors, put longer studs in, and used metric calipers with weld on mounts. Works great and did not change anything else.
  11. Replies
    5
    Views
    529

    Do you open the gap?

    Do you open the gap?
  12. Replies
    5
    Views
    529

    Spark plugs

    What spark plugs do you use in a oval port, open chamber head? (brand and # )
  13. Replies
    7
    Views
    903

    You can mount it from the engine block with two...

    You can mount it from the engine block with two 1" straps welded together. I will get a picture of it this weekend.
  14. Replies
    3
    Views
    575

    D4 Intake

    Looking for a D4 Intake to buy. Must be stock with no porting. Let me know what you have. Thanks
  15. Replies
    4
    Views
    941

    Hoosier Dirt Bozz medium on 8" rims

    Hoosier Dirt Bozz medium on 8" rims
  16. Replies
    4
    Views
    941

    Black Slick Track

    So I go to this race every year and the track slicks off. You would think that it is laying rubber down but it is black slick and drives almost like driving on ice. I see all the cars are having the...
  17. Replies
    9
    Views
    1,737

    Looks as it will be cheaper to get a 8.8. That...

    Looks as it will be cheaper to get a 8.8. That way, I can use a 3.55. Found one at the junkyard for $100.00.
  18. Replies
    10
    Views
    4,271

    Southwest speed carries the right rear floater...

    Southwest speed carries the right rear floater for $ 88.00.
  19. Replies
    10
    Views
    4,271

    Post from another thread. FASTBOYS leaf...

    Post from another thread.

    FASTBOYS leaf tech(get it here)
    Let's try this one more time
    I am not too good at this typing and spelling thing, but I think you can get what you need to know about...
  20. Replies
    11
    Views
    778

    Had this exact same issue a month or so ago. Had...

    Had this exact same issue a month or so ago. Had to switch from an MSD box to a TFI and every time I would pull the trigger on the timing light it would go to missing. I could run the timing light...
  21. Replies
    10
    Views
    4,271

    Will it work? Yes. I have run this setup for the...

    Will it work? Yes. I have run this setup for the past three years. If you are on a tacky hooked up track I would lock the floater anyways on a camaro. Now if your running on a dry slick track and...
  22. Replies
    9
    Views
    1,737

    OK, where can I get something aftermarket for a...

    OK, where can I get something aftermarket for a 7.5?
  23. Replies
    9
    Views
    1,737

    Ford 7.5 rear end

    Are there any gears available for the 7.5 between 3.45 and 3.73?
  24. Replies
    6
    Views
    1,087

    I use the aluminum spring eye bushing. Its either...

    I use the aluminum spring eye bushing. Its either a 1/2" or 9/16" bolt hole through the center. Use a lock nut on the bolt so not to tighten down on the bearings.
  25. Replies
    6
    Views
    1,087

    Day Motorsports has them. Part #AFC-20235-2

    Day Motorsports has them. Part #AFC-20235-2
Results 1 to 25 of 50
Page 1 of 2 1 2

All times are GMT -5. The time now is 03:27 PM.


Powered by vBulletin® Version 4.2.0
Copyright © 2014 vBulletin Solutions, Inc. All rights reserved.