Search:

thats a nearly stock motor, just higher compression and a cam with .100 more lift that stock, so what do you think?

i think a 350 holley

if you really want to go fast
and i suggest you get...

How much do you charge?
Rebco has 6 mills setup just for piston operations

What crank angle does peak pressure occur at?
It is long before the rod and crank throw reach 90 degrees.
This minimizes the effect your speaking of

That would be delta cams in Washington he reground it for me
He said some people use dimes.....
Esslinger says .040-.050

lre is right
people think the bbss motors lack the torque
they are fear mongers
the displacement is the same

but guess what, the bbss motor cuts down on friction and allows for less valve...

hey ive never dealt with hydraulic lifters before only solids,
im using a reground ranger roller cam (super mild)
whats the ideal lash with a collapsed lifter to avoid lifter pump up
does anyone...

http://www.innovatemotorsports.com/products/MTXL.php
and a pocket full of micro drills

displacement is a much more important operating parameter than rod to stroke ratio
r/s does make a difference
but there are prostock engine builders that will tell you the rod just connects the...

Hello,
i'm looking for a small port dual plug mustang, or ranger head 1995+


email me
englertracing@yahoo.com
Thanks,
Aaron

Im looking for a ford 2.5L or larger crank
email me
englertracing@yahoo.com

Thanks,
Aaron

Just watch out for any rod over 550grams.
They're over built imho if they weigh more.

Chuck that 1% front weight in the trash.
Years ago we had some rough driving going on my sway bar bracket broke and the car went faster....
Left it off since.
The scales like it too.

Double thumbs up! What's it for?

@ dan32 I know offset pistons work but Id be willing to bet that crank offset would beat piston offset every day. They sort of do the same thing. But the long side of the piston will create more...

I know it works or a Prius wouldn't use it.

I just wonder how much and if anyone around here has done it to a pinto.
Would be really sneaky to do to at a track that has real tear down tech.

No.

Think about the extreme of this. Move the con rod to one side of the piston. Now the piston trys to rotate around the pin causing more friction. Race pistons aren't offset. Stock ones are...

Just what will I offset grind on a 3.5 stroke crank? And 5.75 rods. The point is to increace rod angle btdc and decreace rod angle atdc at the bottom it does the opposite. Basically the benefits of...

I didn't think of this I wonder if its possible to get nearly the same offset this way.. although I'm already hard pressed to get my rod and crank to fit in the block this will cause one side of the...

I'd like to try it. I'm sure it will help. I'm not sure how much it will help. I was hoping to hear from someone who has done it and can say it runs better. I sure didn't even think of the trans...

Hey someone told me that cambered rear ends don't last long.
I saw they have a ball drive setup that looks like it would last forever on the winters site.
I would imagine they would be like this...

Does anyone see any disadvantages to a 4 bar with A 5th coil on asphalt? I watched a video of some dlms on a short track and one of them set the overall track record.

Has anyone ever put a large journal crank in a small journal block but offset it to the left?
If you don't know what I'm talking about it would act like a long rod on the way down and a short rod on...

http://www.not2fast.com/chassis/mumford.shtml
This is going to be the lateral location device.

Im still thinking r/s would be bad on pavement. Most stock vehicles the outside of the car gets...

I didn't think I would want rear steer. In my book race car vehicle dynamics it says rear steer in the direction we use on dirt, on asphalt, it will steer itself tighter roll more, and steer more...

Hello late model guys.
Currently I run a ministock.
I'm building a road/hillclimb special if you don't know what hill climb is, its basically like an asphalt rally up a hill.
I'm using a bunch of...