Search:

Type: Posts; User: 14flower

Page 1 of 6 1 2 3 4

Search: Search took 0.32 seconds.

  1. Replies
    0
    Views
    359

    flat top 383 sbc

    i have a 383 sbc scat light weight crank i beam rods falt top srp 21 degree pistons with 1/16 1/16 5/16 ring lands.big hyd. flat tappet cam or mild solid flat tappet cam. double humb heads bowl...
  2. Thread: 383

    by 14flower
    Replies
    1
    Views
    504

    383

    would anyone on here on the west coast be interested in a flat top 383 6inch rod iron head motor ?idk how many people are on here from cali.
  3. how much duration @.050 is needed to make power up to 8k on a ford 2.3

    been looking at camshafts and wondering if anyone would have some knowledge on this. i see lots cam makers say there cams are good to 7800 with only 240degrees at .050 then some say 270 so will both...
  4. Replies
    12
    Views
    1,118

    for got to add also had to remove the power valve.

    for got to add also had to remove the power valve.
  5. sounds like accelerator arm misadjusted or wrong...

    sounds like accelerator arm misadjusted or wrong cam
  6. Replies
    12
    Views
    1,118

    well once we installed a thermostat and got the...

    well once we installed a thermostat and got the engine temp up to 180 we found that we where over jeted got some smaller 128-130 jets and now runs fine with just a light light darkish cream color...
  7. Replies
    1
    Views
    1,460

    ford 2300 roller cam

    need a .580 or bigger solid roller cam send what u got and full spec sheet if u can need asap
  8. Replies
    15
    Views
    2,101

    race fuel not enough compression for e85

    race fuel not enough compression for e85
  9. Replies
    15
    Views
    2,101

    i wouldnt go over 200cc lose to much acceration....

    i wouldnt go over 200cc lose to much acceration. not enough hp or cubic inches for that big of head.id run a super victor copy from procomp they are more even flow from runner to runner. get some...
  10. Replies
    4
    Views
    590

    bigger pump mite had more pull check pick up tube...

    bigger pump mite had more pull check pick up tube and have the pump one y doind so and make sure u feel the end pof it to see if its sucking and start taking ur hoses off ffrom the carb back til u...
  11. Replies
    12
    Views
    1,118

    150 with the big cam and 250 with are smaller one

    150 with the big cam and 250 with are smaller one
  12. Replies
    12
    Views
    1,118

    yes its a 4banger carb and he sent us carb with...

    yes its a 4banger carb and he sent us carb with those jets built for the engine its on. and we dont use a oil cooler or temp gauge i know its hot engone cause to filter is to hot to hold ur hand on....
  13. Replies
    7
    Views
    1,123

    turn the idel screws out on the metering blocks...

    turn the idel screws out on the metering blocks 11/4 turns and see if itll light off without touching the throtle
  14. Replies
    12
    Views
    1,118

    also forgot to say went from 134-136 up to...

    also forgot to say went from 134-136 up to 136-138 and seem to help a bit then went up to 138-140 for the main and got worse should i just lean it out to see if itll build heat ?
  15. Replies
    12
    Views
    1,118

    ran the car friday with .025 plug gap runs great...

    ran the car friday with .025 plug gap runs great til u go past a little over 1/2 throttle then breaks up again cant get it to warm up past 160 runing on the track and then got a flat car warmed up...
  16. Replies
    6
    Views
    783

    pump gas no need for race fuel with that low...

    pump gas no need for race fuel with that low compression
  17. Replies
    6
    Views
    783

    agreed in less u can find a good deal on a set of...

    agreed in less u can find a good deal on a set of 200 and smaller darts or rhs heads 650 double pumper quick fuel carb if u got the money and at least a wilson brothers spacer with a air gep rpm...
  18. Replies
    15
    Views
    2,101

    and intake will need to know what rpm you want...

    and intake will need to know what rpm you want that baster to turn and run at ? cam will need to know that as well
  19. Replies
    15
    Views
    2,101

    just remember on pump gas u can only got...

    just remember on pump gas u can only got 9.8-10.1ish :1 on iron heads my sugesstion is go e85
  20. Replies
    15
    Views
    2,101

    well you said any heads so u got ask ur self what...

    well you said any heads so u got ask ur self what fuel u want to run pump or 110 ? you could buy a set of afr 185 heads sence u said any 23 head and run 10.5-11:1 on pump gas or a set of rhs or dart...
  21. Replies
    4
    Views
    755

    sence its not a svo blobk theres no difference...

    sence its not a svo blobk theres no difference over a normal 2.3 block. u could shave the crap out the hed and just re ring it sence the stock pistons are forged. head studs a must and at least bowl...
  22. Thread: Pistons

    by 14flower
    Replies
    18
    Views
    2,345

    agreed if ur already running good pistons and...

    agreed if ur already running good pistons and theres nothing wrong with them just chane out the pin never seen a pin lighter then 52 grams but depending how heavy urs are u mite gain alot also have u...
  23. Thread: Pistons

    by 14flower
    Replies
    18
    Views
    2,345

    well idk if it would be cheating in is divison...

    well idk if it would be cheating in is divison never seen a forged piston weight so much mine are 261 with pin and rings my rods pistons pin rings a bearings weight 520 so figured he had to use like...
  24. Thread: 2 questions

    by 14flower
    Replies
    6
    Views
    1,770

    you will lose top end tourque 383's start to...

    you will lose top end tourque 383's start to drop off tq after 6500 rpm idc what parts u use in side it just the way the bore to stroke works out. but your top end rpm u can turn and the snappyness...
  25. Replies
    15
    Views
    2,101

    do you have any parts to start off with ?

    do you have any parts to start off with ?
Results 1 to 25 of 139
Page 1 of 6 1 2 3 4

All times are GMT -5. The time now is 07:42 PM.


Powered by vBulletin® Version 4.2.0
Copyright © 2021 vBulletin Solutions, Inc. All rights reserved.