Search:

Type: Posts; User: ace1

Page 1 of 7 1 2 3 4

Search: Search took 0.30 seconds.

  1. Replies
    2
    Views
    679

    I think I'll keep it on what it calls for. Thanks

    I think I'll keep it on what it calls for. Thanks
  2. Replies
    2
    Views
    679

    Left Frt. Upper Control Arm Mounting

    I need a left upper control arm for a 08 Mastersbilt. Calls for a 10 1/4". It mounts to the inside of the frame. If I can't find a 10 1/4, would there be any issues using a shorter and mount on the...
  3. Thread: 602 Fuel

    by ace1
    Replies
    2
    Views
    553

    E85 is legal as of this year.

    E85 is legal as of this year.
  4. Thread: 602 Fuel

    by ace1
    Replies
    2
    Views
    553

    602 Fuel

    What fuel are you running in your 602? I have been using 110 race gas. Is it really any better than pump gas for these motors. I know pump is recommended from factory.
  5. Replies
    0
    Views
    908

    Mastersbilt Spindles

    What is the difference in the standard Mastersbilt Smackdown and S7 spindles. Are there markings or a way to measure and find out what I have?
  6. 1-2 years old. Marshall, TX. My dad raced there...

    1-2 years old. Marshall, TX. My dad raced there around 1964-1966
  7. Thread: RR shock angle

    by ace1
    Replies
    4
    Views
    2,575

    It looks to be added but might not be. The welds...

    It looks to be added but might not be. The welds don't look the same but they did a very good job. So moving inward will soften spring and add drive? I'm on non adjustable shocks. If I have the car...
  8. Thread: RR shock angle

    by ace1
    Replies
    4
    Views
    2,575

    RR shock angle

    I have a 08 Mastersbilt that has had a shock mount added to the chassis on the RR which will lean the shock more in toward center of car. What's the thoughts on moving it in? What would be more...
  9. Thread: DIY Tire machine

    by ace1
    Replies
    6
    Views
    2,041

    I saw one made from a small winch. They just used...

    I saw one made from a small winch. They just used the motor and rigged up a coupler. Mounted a battery on the stand and just used 12v.
  10. Replies
    0
    Views
    1,573

    Mastersbilt rear deck height

    08 mastersbilt. What is the height of the rear deck support. I know rules may have a lot to do with it. But if making a new rear deck support how long would you make the tube to the bumper. Iím not...
  11. Replies
    3
    Views
    2,052

    View Post

    36 1/2

    I donít know why I have to put 10 characters in the post.
  12. Replies
    3
    Views
    2,052

    Aluminum drive shaft?

    I donít see many if any aluminum drive shafts in my area. What are thoughts on these. Iím needing one and found a used one from a reputable source. Iíve only used steel in the past.
  13. Replies
    8
    Views
    2,269

    I have one of the wissota cars I'm getting...

    I have one of the wissota cars I'm getting together. Its a 08 I'm told, round tube 01370W. The engine is set back more. My son has a 08 square tube and I have to use a shorter drive shaft than his...
  14. Replies
    0
    Views
    1,397

    08 Mastersbilt Wissota setup? edited

    What are differences in the Wissota and Std. smackdown chassis? I have found the engine is set back different and the rear end doesn't set the same left to right. I have 17" instead of 15 3/4 from...
  15. Replies
    5
    Views
    2,128

    Is there any other differences on the wissota...

    Is there any other differences on the wissota cars. I was just checking the rear end side to side and it doesn't measure to the book spec.
  16. Replies
    5
    Views
    2,128

    That is it. It does have a W. I wondered about...

    That is it. It does have a W. I wondered about that. Thanks
  17. Replies
    5
    Views
    2,128

    17.5/15.5 both sides

    17.5/15.5 both sides
  18. Replies
    5
    Views
    2,128

    08 Mastersbilt drive shaft length

    We have 2 08 Mastersbilt cars, one square tube, one round tube. Standard slip yoke Bert trans in both. The square tube is using a 38" drive shaft but a 38 is too long for the round tube. It likes...
  19. Replies
    6
    Views
    2,485

    Oh no, I'm not. I found a crack in it around the...

    Oh no, I'm not. I found a crack in it around the starter cup any way. I'll keep my steel bell in for now. Thanks
  20. Replies
    6
    Views
    2,485

    I think that is the one I have. The hole is about...

    I think that is the one I have. The hole is about 5 1/8". But I don't have an adapter.
  21. Replies
    6
    Views
    2,485

    GM Aluminum Bell Housing

    Will a stock GM aluminum bell housing be ok for a crate car. I think it would be as good as the bert or brinn. Most of those have been cracked and repaired.
  22. Thread: LR Brake Floater?

    by ace1
    Replies
    15
    Views
    3,361

    Got it. Thanks

    Got it. Thanks
  23. Thread: LR Brake Floater?

    by ace1
    Replies
    15
    Views
    3,361

    Thanks for the tips and suggestions. I will give...

    Thanks for the tips and suggestions. I will give it a go, play around with it some and see what happens. I'm getting out of a 04 GRT and into the 08 Mastersbilt. Should I expect a big difference in...
  24. Thread: LR Brake Floater?

    by ace1
    Replies
    15
    Views
    3,361

    I won't have to worry about that where I'm at. I...

    I won't have to worry about that where I'm at. I could probably run one and get away with it. Once I find the position of the floater that works best, it will stay at that position when making bar...
  25. Thread: LR Brake Floater?

    by ace1
    Replies
    15
    Views
    3,361

    View Post

    Iím not sure what is on it but the left look good. The right were wore out.
Results 1 to 25 of 164
Page 1 of 7 1 2 3 4

All times are GMT -5. The time now is 01:35 PM.


Powered by vBulletin® Version 4.2.0
Copyright © 2022 vBulletin Solutions, Inc. All rights reserved.