Search:

Type: Posts; User: HRE

Search: Search took 0.47 seconds.

  1. Thread: Tire temps

    by HRE
    Replies
    7
    Views
    1,904

    at first setup my RR was hotter than LR. I added...

    at first setup my RR was hotter than LR. I added RR weight and evened up the temps. I am within 20 degrees and my car is pretty good.
  2. Thread: Tire temps

    by HRE
    Replies
    7
    Views
    1,904

    not on my car, Lr cooler than RR and i have...

    not on my car, Lr cooler than RR and i have plenty of drive. but i dont run much stagger either. As you said the tire is spinning faster, so if you add more weight to it the tire would grip more and...
  3. Thread: Tire temps

    by HRE
    Replies
    7
    Views
    1,904

    feed the heat. need more weight on the right...

    feed the heat. need more weight on the right tire. tire is hot because its not gripping, its spinning.
  4. Replies
    56
    Views
    12,310

    When you are resetting your ride heights you're...

    When you are resetting your ride heights you're not setting the spring to the same length as it was before, you're resetting your chassis ride height.
  5. Replies
    56
    Views
    12,310

    lets try this. if you have weight jacks, and you...

    lets try this. if you have weight jacks, and you measure the stick out of the jack bolt say 3 inches and have a set ride height then you change springs from a 225 to a 200. then you reset your ride...
  6. anyone run a Brinn Predator trans? have a question.

    this is where the clutch line goes into the cover. what thread is it NPT or orb? looks to be 1/8 something. thanks
  7. anyone run a Brinn Predator trans? have a question.

    this is where the clutch line goes into the cover. what thread is it NPT or orb? looks to be 1/8 something. thanks
    sorry about posting in the classifieds!
  8. Replies
    5
    Views
    2,117

    afco 20187

    afco 20187
  9. Thread: UMP Motor

    by HRE
    Replies
    2
    Views
    1,625

    Too much friction in the big stroke stuff, hard...

    Too much friction in the big stroke stuff, hard on parts. 3.75 or smaller on the stroke. 3.875 max. Shorter stroke will make the same power, its just moves the peak power up to a little higher RPM....
  10. Replies
    12
    Views
    3,461

    Easy 700 hp on our DTS dyno non inflated numbers...

    Easy 700 hp on our DTS dyno non inflated numbers
    can give references to how they drive if needed
    Callies Magnum 3.625 stroke
    Callies ultra rod 6.125
    cnc ported heads track 1 x heads
    jesel...
  11. Replies
    0
    Views
    513

    Holley HP 950 alcohol carb for sale.

    Nice alcohol HP carb, could use a gasket kit. 0-80498-1 asking 425.00
    812-926-0019
  12. Replies
    0
    Views
    354

    Holley HP 950 alcohol carb for sale.

    Nice alcohol HP carb, could use a gasket kit. 0-80498-1 asking 425.00
    812-926-0019
  13. Replies
    0
    Views
    459

    Holley HP 950 alcohol carb for sale.

    sorry wrong section
  14. Replies
    0
    Views
    418

    NIB Callies Magnum XL crank

    New Magnum XL crank 3.625 stroke 350 mains 2.100 rod pin 41 lbs $1800.00
    Houseracingengines@comcast.net
  15. Replies
    0
    Views
    464

    NIB Callies Magnum XL crank

    New Magnum XL crank 3.625 stroke 350 mains 2.100 rod pin 41 lbs $1800.00
    Houseracingengines@comcast.net
  16. Replies
    7
    Views
    800

    Valve covers

    Pm sent check you inbox
  17. Replies
    8
    Views
    1,476

    Landrum springs don't seem go away as quick as...

    Landrum springs don't seem go away as quick as the others do.
  18. Replies
    6
    Views
    4,356

    Those Lightnings are fast cars keep up the good...

    Those Lightnings are fast cars keep up the good work Don.
  19. Replies
    0
    Views
    543

    Dart 227 cnc heads, Jesel rockers

    Complete set of heads. Ferrea comp plus valves, comp 26089 springs 12 races. Jesel sportsman rockers 2400.00
    Houseracingengines@comcast.net
  20. Replies
    0
    Views
    785

    Pro tools one shot tube bender

    Pro tools one shot bender 15 ton ram HB302 model. 1.5 , 1.25 dies. , air over hyd pump, pro tools stand, support/follow bar. Works great NO PROBLEMS. over 2800 new 2000 shipped...
  21. Replies
    0
    Views
    513

    Pro tools one shot tube bender

    Pro tools one shot bender 15 ton ram HB302 model. 1.5 , 1.25 dies. , air over hyd pump, pro tools stand, support/follow bar. Works great NO PROBLEMS. over 2800 new 2000 shipped...
  22. Replies
    0
    Views
    664

    Pro tools one shot hyd. Tube bender

    Pro tools one shot bender 15 ton ram HB302 model. 1.5 , 1.25 dies. , air over hyd pump, pro tools stand, support/follow bar. Works great NO PROBLEMS. over 2800 new 2000 shipped...
  23. Thread: 400 sbc build

    by HRE
    Replies
    2
    Views
    1,237

    Any Rules?

    Any Rules?
  24. Hey Sandy when are you going to send the info to...

    Hey Sandy when are you going to send the info to westhold. No feature lap times for 8/4 and no lap time for 8/11?
Results 1 to 24 of 24

All times are GMT -5. The time now is 05:02 AM.


Powered by vBulletin® Version 4.2.0
Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.