Search:

Type: Posts; User: little302

Page 1 of 3 1 2 3

Search: Search took 0.32 seconds.

  1. Thread: fly wheels

    by little302
    Replies
    12
    Views
    3,726

    Use the 2.0 from the 70's.. Its 10.4 lbs bare.....

    Use the 2.0 from the 70's.. Its 10.4 lbs bare.. Use the whole 2.0 setup.. 23 spline...Simple... Just have it drilled for the 2.3 crank.. Works great...My Pinto flywheel was 21 lbs. So I lost nearly...
  2. Replies
    8
    Views
    2,525

    The 70 -72 2.0 is 10.4 lbs..Its a 23 spline.....

    The 70 -72 2.0 is 10.4 lbs..Its a 23 spline.. have it drilled to fit the 2.3 crank. Simple.... light...Use the 2.0 clutch and pressure plate.
  3. Replies
    1
    Views
    1,564

    Yes.. Just last week on an open chamber D port..

    Yes.. Just last week on an open chamber D port..
  4. Replies
    9
    Views
    2,383

    Im thinkin you need to check your final...

    Im thinkin you need to check your final drive..Never heard of a 2.56.. Love to have something that low though!
  5. Replies
    6
    Views
    1,893

    Id lean toward carb or timing.. Ive turned a...

    Id lean toward carb or timing.. Ive turned a completely stock 88 Stang motor 7200 before the springs gave way..
  6. Replies
    7
    Views
    2,099

    Battling the same problem with a friends carb. He...

    Battling the same problem with a friends carb. He over looked one simple thing..Did you "tune" the carb with the mixture screws and a vacuum guage? If not You are giving up a valuable tuning...
  7. Replies
    7
    Views
    1,978

    toynv.. I honestly have no idea.. The 32/36 got...

    toynv.. I honestly have no idea.. The 32/36 got loaned out and I decided to race, so we bolted it on... Ran good so we never touched it...Probably alot more perfomamce there waiting to be untapped. ...
  8. Replies
    7
    Views
    1,978

    I use the 38mm too, but was wondering the same...

    I use the 38mm too, but was wondering the same thing as I have two of them..
  9. Replies
    1
    Views
    1,063

    I recommended him to a local guy too...

    I recommended him to a local guy too...
  10. Thread: Gearing help

    by little302
    Replies
    8
    Views
    1,952

    I run a 3.80 with the 2.14 with 15's and a...

    I run a 3.80 with the 2.14 with 15's and a rollout of 88 on the RR. Not great for restarts, but once you get moving you fly by on the top.Thats an 8.13 uncorrected. 7300...Thats a high bank!
  11. Replies
    7
    Views
    2,108

    Is that the BP classic GL4? Does nobody run...

    Is that the BP classic GL4? Does nobody run synthetics?
  12. Replies
    2
    Views
    1,107

    I use a power rack with a quickener. No probs.

    I use a power rack with a quickener. No probs.
  13. Replies
    9
    Views
    2,086

    I have an 80 Bobcat/Pinto with a 2 to 1...

    I have an 80 Bobcat/Pinto with a 2 to 1 quickener, and no P/S. Never had it never will.. no problems
  14. Replies
    4
    Views
    1,683

    According to desktop dyno Im at 219, and mine...

    According to desktop dyno Im at 219, and mine isnt that complicated, or expensive.. So im sure 200 is reachable..
  15. Replies
    5
    Views
    2,088

    As 22 dodge would say. Use the Mopar 2.2 spring...

    As 22 dodge would say. Use the Mopar 2.2 spring and run it for 5 years!!;)
  16. Replies
    4
    Views
    1,411

    We run the heavy 5/8 coarse used commonly on dirt...

    We run the heavy 5/8 coarse used commonly on dirt cars, with 1 inch nuts..
  17. Replies
    2
    Views
    1,257

    One guy commented a few years ago on angle...

    One guy commented a few years ago on angle milling.. Limited success..
  18. Thread: Best oil?

    by little302
    Replies
    17
    Views
    3,975

    Mobil 1 synthetic after break in..Bearings look...

    Mobil 1 synthetic after break in..Bearings look new after a season.. Seen it in 4 cyl and multiple V8 cars..Enought to make me trust their 15,000 mile stuff in my daily...For a low budget racer it...
  19. Replies
    3
    Views
    1,300

    Id run a Saturn. Lighter weight, and less HP but...

    Id run a Saturn. Lighter weight, and less HP but they make good power, and are balanced pretty well.. You never said dirt or asphalt though.
  20. Replies
    11
    Views
    2,579

    Ill have to chime in here.. Im usually quiet and...

    Ill have to chime in here.. Im usually quiet and absent, but needed some advice so I logged on today.. We ran 15's because of cost.. Tires were plentiful in our area used from modified teams so that...
  21. Replies
    11
    Views
    2,320

    Exactly!! TFI is great.. If you buy from parts...

    Exactly!! TFI is great.. If you buy from parts store, it will run you $100, get it from the bone yard.
  22. Thanks.. Much appreciated!!

    Thanks.. Much appreciated!!
  23. cutting tool for mech lifter in 2.3 head..help..

    Esslinger no longer carrys them.. Who does.. My machinist doesnt have one as 4 cyl racing is not popular in our area.. Thanks in advance
  24. Thread: 2300 vs 2000

    by little302
    Replies
    3
    Views
    1,192

    And to answer your question.. NO.. The early...

    And to answer your question.. NO.. The early 70's 2000cc does NOT interchange in any way with any 2.3.
  25. Thread: D4 Intake

    by little302
    Replies
    3
    Views
    1,057

    Send me a txt.. i think I have one put away.. 573...

    Send me a txt.. i think I have one put away.. 573 208 3528.
Results 1 to 25 of 73
Page 1 of 3 1 2 3

All times are GMT -5. The time now is 04:35 PM.


Powered by vBulletin® Version 4.2.0
Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.