|
|
Search:
Type: Posts; User: hot_rod
Search:
Search took 4.36 seconds.
-
I have been trying to figure out what u joint I need to use for my street stock this year. I have searched on here and really could not find anything. I am looking for a combination u joint that...
-
I run 13 on left and 15 on right side with a 3250lb metric chassis on Hoosier Emod tires. The ones that the UMP modifieds run. I try to keep the tire pressures simple so I can remember them easy...
-
Well I realize that this thread is a little older, but we finally got it all lined out and working pretty decent. Once we got the new motor together we had issues with it running correctly, ended up...
-
You can measure the pistons and find their specs. In a SBC you are attempting to acheive a 9" deck height. You can do the math and figure out what they fit fairly easily. DH=Rod Length+Compression...
-
what kind of coil are you using? If your using something like the Blaster 2 (red can MSD 8202) it is oil filled and has to be installed vertical or even with a slight lean towards the left side of...
-
We have the majority of the weight mounted directly behind the rear end on either side. We also have some in front of the rearend and over top of it. The car is built like a modified, the only...
-
I appreciate everyones opinion. I had a buddy that drives a modified tell me that adding bite would loosen me in and tighten me coming off. It just went against what I thought I knew about adding...
-
I was wondering what adding bite would do to a car that is already tight in and loose off would do to it. I am running ~155lbs of bite right now. We built a new car last and really dont have a lot...
-
i would check the valves, might be to tight. Intake valves may not be not sealing against the seat.
-
-
Thanks, I appreciate the help.
-
I have recently purchased four new Hoosier Emod tires 3 D's and 1 A. I was wondering what all needed to be done before I put them on track. I.E. Do they need to be cleaned or are they good run as...
-
-
According to a dyno program on my laptop, Dyno2000. Adding 5CI by increasing the stroke from 3.48 to a 3.53, will net you 1 HP at 6000rpm. Adding 5CI by increasing the bore from 4.030 to 4.060 will...
-
-
For Sale: GM Metric UMP Street Stock roller chassis. This car has everything to go racing except for motor/tranny/shifter/gear. Car is legal for UMP with the exception of the brake bias adjuster,...
-
Fel-Pro VS12869T. These gaskets have a metal shim embossed into them and they seal pretty good. Completey reusable. Also, with stock heads, I would recommend upgraded to a cast aluminum valve...
-
We have ran their solid flat tappet cam for a season with no issues. The cam will go into our backup motor this year, since we can run roller cams now. Good cam for the money.
-
I took a 13" 250lb LR out and put in a 16" 100lb, night and day difference. You can figure up what spring rate you will need by measuring the compress height of your original spring and multiplying...
-
I run the Contour GPS. I really like it. I bought the roll cage mount and it is very sturdy, IMO. The lens on the camera will rotate upto 180* to allow you to mount the camera in a odd position...
-
just run Stage 8 Locking fasteners.
http://www.summitracing.com/search/product-line/stage-8-locking-header-bolt-kits/make/chevrolet/engine-size/5-7l-350/circle-track/yes
-
I have been looking at getting a R2C for my Super Street. I was curious as to whether or not it was worth spending the money and get the actual R2C filter base that fits the 4150 carb? Or will the...
-
I have an Impact Wizard that is SA2005 certifited. It is pretty close to 3 years old now. I have been extremely pleased with it. It is not the lightest or the cheapest, but it is definetly not...
-
a 350SBC block with a bore of 4.015 and a stroke of 3.75 gives you a 379.8 and 4.020 and 3.75 gives you a 380.8. Or a 400SBC with a 4.125 bore with 3.562 stroke that another thread on here is...
-
We were able to work on it yesterday. We put a compression gauge on all the cylinders and only had 95 at the most. Most cylinders were around 80 to 85. We put some oil in the cylinders and were...
All times are GMT -5. The time now is 10:41 PM.
|
|