Search:

Type: Posts; User: car62

Page 1 of 20 1 2 3 4

Search: Search took 0.25 seconds.

  1. Thread: Foxbody setup

    by car62
    Replies
    1
    Views
    355

    I've ran it...assuming you are on asphalt?

    I've ran it...assuming you are on asphalt?
  2. Thread: I am stumped

    by car62
    Replies
    2
    Views
    154

    Also check for bent balljoint

    Also check for bent balljoint
  3. I've got one without the shifter

    I've got one without the shifter
  4. Replies
    2
    Views
    774

    Still have 2 sets available

    Still have 2 sets available
  5. Replies
    11
    Views
    1,026

    www.racerwalsh.com

    www.racerwalsh.com
  6. Replies
    11
    Views
    1,026

    Racer Walsh certainly is open

    Racer Walsh certainly is open
  7. Replies
    11
    Views
    1,026

    have you considered going with a heavier...

    have you considered going with a heavier clutch/flywheel combo?
  8. Replies
    12
    Views
    955

    go with a Melling M-127 pump, also check your...

    go with a Melling M-127 pump, also check your main clearances...or just buy a motor from me,custom built to your specs!!!
  9. Replies
    4
    Views
    404

    yes oil will come gushing out,slow down the drill...

    yes oil will come gushing out,slow down the drill speed,all you are doing is priming the engine,just make sure you are going clockwise
  10. Replies
    12
    Views
    955

    could be sucking air somewhere,could be wront...

    could be sucking air somewhere,could be wront bearing tolerances, could be weak oil pump
  11. Replies
    2
    Views
    792

    Yeah,just shoot me a text at the number posted...

    Yeah,just shoot me a text at the number posted and I'll send a couple pics
  12. Replies
    2
    Views
    774

    2 sets gone, 2 sets still available

    2 sets gone, 2 sets still available
  13. Replies
    2
    Views
    792

    Ford 2300 Solid Roller Race Head

    .630 lift billet cam
    strapped towers
    milled .100
    Manley 1.79 valves
    hardened seats
    single wire beehive springs
    titanium retainers
    D-port close chamber,laid over at 45 degree angle and shaped...
  14. Replies
    0
    Views
    336

    Ford 2300 Hardened 1 piece Followers

    14 sets on the shelf
    $111 a set shipped to you(usa)
    Text is best 208-625-1528
  15. Replies
    2
    Views
    774

    Ford 2300 Anti-Pump Lifters

    i have 4 brand new sets left
    $160 a set shipped to you(usa)
    Text is best 208-625-1528
  16. Thread: Blown Engine

    by car62
    Replies
    25
    Views
    2,943

    ive run 38 degrees with a 5.7 rod 2.5 and never...

    ive run 38 degrees with a 5.7 rod 2.5 and never had an issue,ive also taken apart rods that the bearing was completely gone in and they were still proprly torqued, my guess is whoever assembled the...
  17. Thread: Holley 4412 HP

    by car62
    Replies
    12
    Views
    3,853

    when they discontinued the HP and replaced it...

    when they discontinued the HP and replaced it with the XP it seems to have corrected alot of issues,the XP carb is so much more responsive than the HP on the exact same engine with same jets and PV...
  18. Replies
    1
    Views
    597

    Just a follow up, i found out the info i needed,...

    Just a follow up, i found out the info i needed, it is referred to as a T-9 transmission and has a 2nd gear ratio of 1.81
  19. Replies
    6
    Views
    1,307

    Old Rob, i also sent you a PM on some lifter...

    Old Rob, i also sent you a PM on some lifter inserts
  20. Replies
    8
    Views
    1,165

    PM sent, for some reason when someone PM's me im...

    PM sent, for some reason when someone PM's me im not getting any email notification...anyone else having this issue?
  21. Replies
    8
    Views
    1,165

    heck, i even have a set of the Delta lifters that...

    heck, i even have a set of the Delta lifters that were .060 taller than stock,for use with their reground cams..i think they were also anti-pump
  22. Replies
    8
    Views
    1,165

    being the "collector" that i am, i have 3 new...

    being the "collector" that i am, i have 3 new sets on the shelf
  23. Replies
    1
    Views
    597

    Transmission help please

    Have a transmission,the tag says FOG 5A 18G and above that it says 3597 MB just wanting to know the ratios,it's a 5 speed from 1985 Mercury Merkur
  24. Thread: Holley carb help

    by car62
    Replies
    2
    Views
    1,076

    73 jets, 3.5 power valve, #28 nozzle, Red cam on...

    73 jets, 3.5 power valve, #28 nozzle, Red cam on #1 position, and .125 size holes in blades
  25. Replies
    2
    Views
    798

    im also interested in wiring a MSD-6AL to a...

    im also interested in wiring a MSD-6AL to a tfi...has anyone done this?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

All times are GMT -5. The time now is 12:23 AM.


Powered by vBulletin® Version 4.2.0
Copyright © 2017 vBulletin Solutions, Inc. All rights reserved.