Search:

Type: Posts; User: smokem2024

Page 1 of 2 1 2

Search: Search took 0.17 seconds.

  1. Replies
    4
    Views
    456

    Went to take carb off. No fuel came out of the...

    Went to take carb off. No fuel came out of the line. Wouldn't it supposed to have gas in the line or could I have a weak fuel pump?
  2. Replies
    4
    Views
    456

    Thanks. The carb is rochester 2bbl. I will clean...

    Thanks. The carb is rochester 2bbl. I will clean it to see.
  3. Replies
    4
    Views
    456

    Header glowing RED

    I have a right side header glowing. Last week we got turned over. Got all cosmetic stuff fixed and then this week car has a sputter at low rpm and at full throttle racing right side header is cherry...
  4. Replies
    3
    Views
    390

    Ok since first post I changed master cylinder...

    Ok since first post I changed master cylinder again. Realized I had one for power brakes. I got the right one for manual brakes and now the pedal is spongy. It stops better but just spongy. No where...
  5. Replies
    1
    Views
    222

    Axle Question?

    I run a cutlass with a 8.5 10 bolt rear. It has the bolt in axles. I need to know where I can buy new ones?
  6. Replies
    0
    Views
    516

    Frontend setup question

    Anyone run negative caster on both sides on dirt??
  7. Replies
    3
    Views
    390

    Brake Issue...

    I recently took the brake booster off. I put a master cylinder straight to firewall and hooked up rod and lines. Sitting on stands we bled brakes and have a good pedal and they stop. When you set it...
  8. Replies
    20
    Views
    1,206

    Thanks for the info.

    Thanks for the info.
  9. Replies
    9
    Views
    1,123

    How would I measure the front springs to get the...

    How would I measure the front springs to get the 2" of spring compression?
  10. Replies
    9
    Views
    1,123

    Thanks for the help.

    Thanks for the help.
  11. Replies
    9
    Views
    1,123

    Both right side shocks were compressing all the...

    Both right side shocks were compressing all the way in
  12. Replies
    9
    Views
    1,123

    It would roll all the way over on right side....

    It would roll all the way over on right side. Huge gap between tires and fender/quarters on left side. Then coming out of corners it just rocks like its unstable
  13. Replies
    9
    Views
    1,123

    Spring Rates on Front

    Have a g-body and it has LF-1050 and RF-900. Going through the corner and coming of the car rocks really bad. Are these too stiff?
  14. Replies
    20
    Views
    1,206

    Where do you cut the pads down? In the center?...

    Where do you cut the pads down? In the center? Outside edges?
  15. Replies
    6
    Views
    1,318

    Thanks.....

    Thanks.....
  16. Replies
    6
    Views
    1,318

    LOL...I hear ya. I will look if anyone remembers...

    LOL...I hear ya. I will look if anyone remembers chime on in...
  17. Replies
    6
    Views
    1,318

    Disk brakes on rear 7.5....

    I know it has prolly been talked about numerous times but I can't find it. I have a spare rear 7.5 that I want to convert over to disk. Any good setups using stock parts maybe from something other...
  18. Replies
    11
    Views
    1,741

    Dirt of course. ... is there any other type of...

    Dirt of course. ... is there any other type of racing before the cup series.
  19. Replies
    11
    Views
    1,741

    Thanks.... the reason I ask about the 15" is...

    Thanks.... the reason I ask about the 15" is there are some guys I know running them with imca tires and it just looks like it would be too heavy.?????
  20. Replies
    11
    Views
    1,741

    13" vs. 15" tires and wheels.....

    Any advantage with 15's. What is the lightest 13"wheels
  21. Replies
    3
    Views
    1,130

    Yes and also the block will have a spot on the...

    Yes and also the block will have a spot on the oil pan rail that will need to be notched for rod clearance....
  22. Replies
    5
    Views
    769

    sorry guys i overlooked them in the book...

    sorry guys i overlooked them in the book ...thanks though
  23. Replies
    5
    Views
    769

    4 hole 15' wheels

    Anyone know where to get any...who makes them.
  24. i'm just wandering bout it....anyone know...

    i'm just wandering bout it....anyone know anything....
  25. New aftermarket casting from race engineering??????

    Stock appearing 2300 head from race engineering...anyone running one??? How is it????
Results 1 to 25 of 43
Page 1 of 2 1 2

All times are GMT -5. The time now is 10:53 PM.


Powered by vBulletin® Version 4.2.0
Copyright © 2020 vBulletin Solutions, Inc. All rights reserved.