Search:

Type: Posts; User: superstock50

Page 1 of 4 1 2 3 4

Search: Search took 0.90 seconds.

  1. CIRF, I agree with you in the promoting from open...

    CIRF, I agree with you in the promoting from open wheel ranks! I don't like the street races that muck either. But I still think it is MUCH better than Nascrap!
  2. Switch to Indycar!

    Switch to Indycar!
  3. Krooser, that is absolutely 100% BS. You have to...

    Krooser, that is absolutely 100% BS. You have to show an ID to buy tobacco and alcohol, but not to vote..... Pathetic!!!
  4. Replies
    9
    Views
    484

    Better dead then red!!

    Better dead then red!!
  5. Replies
    2
    Views
    2,398

    With all of the knowledge here, still no...

    With all of the knowledge here, still no suggestions???
  6. Replies
    2
    Views
    2,398

    Shock opinions

    Running a 3200lb metric car on a 3/8's moderate to high banked dirt oval. I last ran RF 1100lb LF 950lb RR 250lb and LR 225lb. I have different spring rates to try. Shocks were RF 6 valve LF 5 valve...
  7. Replies
    5
    Views
    3,233

    Where are you located?

    Where are you located?
  8. Replies
    10
    Views
    500

    All he has to do is open his mouth!!

    All he has to do is open his mouth!!
  9. Replies
    6
    Views
    2,059

    I have ran them on roller motors to cut the flow...

    I have ran them on roller motors to cut the flow to the valvetrain. I only wish I hadn't used them on my non-roller, flat tappet solid cam, "stock rocker", engine. It cost me a set of pretty...
  10. No, not yet. Tried another valvebody, closely...

    No, not yet. Tried another valvebody, closely inspected case and did an air pressure test for the servo and high clutch drum. Both were working fine. Pressure test not possible, cooling ports are...
  11. Replies
    21
    Views
    6,269

    I'm sure he meant 2.05 intake and 1.60 exhaust.

    I'm sure he meant 2.05 intake and 1.60 exhaust.
  12. Bleeder type without jets, Phipps valvebody. I...

    Bleeder type without jets, Phipps valvebody. I have replaced everything but the valvebody and case. Maybe that's the problem. Thanks.
  13. Direct drive powerglide slipping in high

    Anyone have any ideas? Rebuild with new clutches, steels, seals, gaskets and o-rings. Took the pump apart and inspected. Opened up the valvebody and cleaned. Took the valves out and...
  14. Replies
    7
    Views
    3,642

    Ump+10,000$ to be as competitive!

    Ump+10,000$ to be as competitive!
  15. Replies
    4
    Views
    509

    What the fu(k is wrong with freemasonry? Do you...

    What the fu(k is wrong with freemasonry? Do you ever have a clue? I don't like what dezero has to say, but why drag freemasons into this! Do you think the Shriners are evil too? Look into the...
  16. Replies
    28
    Views
    2,953

    I've been done with Nascrap for awhile!! I...

    I've been done with Nascrap for awhile!! I recommend more people watch Indycar. Much better racing!
  17. Replies
    5
    Views
    1,291

    I ran a th350 for 2 years in low gear, hated it!...

    I ran a th350 for 2 years in low gear, hated it! Would smoke the clutches in 2 nights. Yes I was running an oil cooler! It's your call. Just my two cents.
  18. Please PM me with details of the distributors.

    Please PM me with details of the distributors.
  19. Replies
    7
    Views
    425

    Thank you! That was by far the greatest...

    Thank you! That was by far the greatest generation; grew up during the depression, and then WWII. Everyone should spend as much time as possible with these people. We could learn a lot from them.
  20. Replies
    5
    Views
    1,196

    I looked in a couple of my books and can't find...

    I looked in a couple of my books and can't find it anywhere....
  21. What a surprise! Lol, those demorats will so...

    What a surprise! Lol, those demorats will so anything!
  22. Replies
    1
    Views
    1,507

    Left lower arm uphill more than right for more...

    Left lower arm uphill more than right for more foward bite on bottom of the track, but will give up a little stability on the high side.
  23. Replies
    0
    Views
    507

    ISO SBC short block

    I live in SW indiana so I don't want to drive too far. Looking for bomber motor, I have heads and intake. Needs to be GM block(bowtie) is okay, at least 12/1 with my 64cc heads. Solid flat tappet...
  24. Replies
    0
    Views
    823

    ISO SBC short block

    I live in SW indiana so I don't want to drive too far. Looking for bomber motor, I have heads and intake. Needs to be GM block(bowtie) is okay, at least 12/1 with my 64cc heads. Solid flat tappet...
  25. Replies
    8
    Views
    1,674

    What is your contact number?

    What is your contact number?
Results 1 to 25 of 90
Page 1 of 4 1 2 3 4

All times are GMT -5. The time now is 09:52 AM.


Powered by vBulletin® Version 4.2.0
Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.