Search:

changed engine and transmission and after doing this when the engine is running and the hood is raised the RPM of engine increases about 200. when the hood is put back on it decreases 200 rpm. ...

Any one have spring rates for 1' 1 1/8 1 5/16 and 1 3/8 inch Mustang sway bars.

Thanks
TC65

When should the crankshaft be changed in a 2.3 ford ? I have heard they should be changed after each year of racing. Have one that has 10 races on it. It was new last year when installed.

TC65

What is the best way to remove the stock bushing in the front control arms?

thanks
TC65

Anyone use CHEVY valves in a Ford 2300 head Is there an advantage for using them?


Thanks
TC65

Need help and info on installing rear adjustable spring buckets. Materials, where to buy ,etc.

Thanks
Tc65

Thanks Dave I will remember that

The belt was the problem. Using a Gates racing belt which is about 5 years old. It had thin places like it had stretched.
Put a new one and it runs perfect.

Thanks

TC65

Installed new 2300 engine and the timing belt looks like it is going to run off the aux and cam pulleys when running. I have changed the belt tensioner, the cam gear and the belt still moves. The...

I am going to install a 5 speed transmission in our race car. My question is do I need to use a short clutch lever ball or a long one? We used this trans. about 5 yrs ago and think we used the long...

Light Wiseco Pistons and LIght rods. I am not sure but think the pistons are chevy

WE have been running a 5.2 rod bottom end for years and decided to go to a 5.7 rod bottom end. We used everthing from the old 5.2 bottom end, clutch, flywheel, etc. After running the 5.7 bottom end...

I have tried a PM and have not gotten anything,

Thanks Browndog, I have sent them three Emails but have not an answer.

TC65

OLD ROB, How do you order from Powerbyace? Been trying for about 2weeks. No one will answer my Emails.

Thanks
TC65

I have been trying to order rocker studs and nuts from AUTOMOTIVE COMPONENT ENGINEERING. I have sent 3 Emails with the part numbers but have not received a response. Does anyone know if they are...

What is the best combination of heads and intake manifolds? Oval head/oval intake , Oval head/dport intake? Have been running oval/oval with good results. Have run oval/d port and did not see any...

I have 3 Mels distributors and have never used his coils. I have used the stock round and square FORD coils. At present time I am using the MSD FORD TFI blaster coils and have not had any problems....

Wanting to change rotors and calipers on our Mustang race car . We have been using the 9 inch stock rotors and calipers. There is alot of drag using these. Is there any aftermarket rotors and...

Remove the control arms and then measure the center of one bushing to the center of the other bushing. Remove the bushings from the control arms. Weld a piece of 1/4 inch key stock inside where the...

1195 I think and hope you are right. I have a 80 Ford tech and it says to inspect this bushing when changing the seal. I have a tail shaft that is off another trans. and I removed the seal in it and...

It is leaking between the yoke and the seal. I have checked yoke for scratches etc. found nothing. the yoke measures about .003 larger than the seal. The vent is open on plate. Have changed the...

Having problem with the tail shaft seal leaking in our transmission. When the car is sitting in the shop it will leak app. 2oz. when running at the track we do not see any signs of leakage. In the...

Have neen using Victor Reinz head gaskets. Have not had any problems but it takes an hour or so to clean the head and block after the head is removed. What are other choices without the cleanup?
...

Thanks Dave, I watched 7 videos on indexing. Four said index the open end of the grounding strap to the intake valve, two said index to the exhaust valve and other one said to get between the ex. and...