Search:

Type: Posts; User: car62

Page 1 of 20 1 2 3 4

Search: Search took 0.42 seconds.

  1. Thread: 2.3 crankshaft

    by car62
    Replies
    4
    Views
    347

    depends on the rpm

    depends on the rpm
  2. Thread: champion plug

    by car62
    Replies
    4
    Views
    274

    Brisk GR14S

    Brisk GR14S
  3. Replies
    2
    Views
    400

    On TFI the white wire from MSD box(crank...

    On TFI the white wire from MSD box(crank trigger)gets hooked to green wire on TFI
  4. Replies
    1
    Views
    471

    Ford 2.3 head gasket question

    Running the felpro 1035,ran engine for about an hour using head bolts,took head off(can't remember why),now using head stud kit,1035 looks perfect,safe to re-use it? Parts store is 5 days out on...
  5. Thread: Shim oil pump

    by car62
    Replies
    6
    Views
    607

    Definitely don't want washers between tube and...

    Definitely don't want washers between tube and pump,it will suck air...if you want more pressure,go with a Melling M127
  6. Thread: Foxbody setup

    by car62
    Replies
    1
    Views
    852

    I've ran it...assuming you are on asphalt?

    I've ran it...assuming you are on asphalt?
  7. Thread: I am stumped

    by car62
    Replies
    2
    Views
    530

    Also check for bent balljoint

    Also check for bent balljoint
  8. I've got one without the shifter

    I've got one without the shifter
  9. Replies
    2
    Views
    1,113

    Still have 2 sets available

    Still have 2 sets available
  10. Replies
    11
    Views
    1,552

    www.racerwalsh.com

    www.racerwalsh.com
  11. Replies
    11
    Views
    1,552

    Racer Walsh certainly is open

    Racer Walsh certainly is open
  12. Replies
    11
    Views
    1,552

    have you considered going with a heavier...

    have you considered going with a heavier clutch/flywheel combo?
  13. Replies
    12
    Views
    1,428

    go with a Melling M-127 pump, also check your...

    go with a Melling M-127 pump, also check your main clearances...or just buy a motor from me,custom built to your specs!!!
  14. Replies
    4
    Views
    729

    yes oil will come gushing out,slow down the drill...

    yes oil will come gushing out,slow down the drill speed,all you are doing is priming the engine,just make sure you are going clockwise
  15. Replies
    12
    Views
    1,428

    could be sucking air somewhere,could be wront...

    could be sucking air somewhere,could be wront bearing tolerances, could be weak oil pump
  16. Replies
    3
    Views
    1,571

    Yeah,just shoot me a text at the number posted...

    Yeah,just shoot me a text at the number posted and I'll send a couple pics
  17. Replies
    2
    Views
    1,113

    2 sets gone, 2 sets still available

    2 sets gone, 2 sets still available
  18. Replies
    3
    Views
    1,571

    Ford 2300 Solid Roller Race Head

    .630 lift billet cam
    strapped towers
    milled .100
    Manley 1.79 valves
    hardened seats
    single wire beehive springs
    titanium retainers
    D-port close chamber,laid over at 45 degree angle and shaped...
  19. Replies
    0
    Views
    566

    Ford 2300 Hardened 1 piece Followers

    14 sets on the shelf
    $111 a set shipped to you(usa)
    Text is best 208-625-1528
  20. Replies
    2
    Views
    1,113

    Ford 2300 Anti-Pump Lifters

    i have 4 brand new sets left
    $160 a set shipped to you(usa)
    Text is best 208-625-1528
  21. Thread: Blown Engine

    by car62
    Replies
    25
    Views
    3,683

    ive run 38 degrees with a 5.7 rod 2.5 and never...

    ive run 38 degrees with a 5.7 rod 2.5 and never had an issue,ive also taken apart rods that the bearing was completely gone in and they were still proprly torqued, my guess is whoever assembled the...
  22. Thread: Holley 4412 HP

    by car62
    Replies
    12
    Views
    4,459

    when they discontinued the HP and replaced it...

    when they discontinued the HP and replaced it with the XP it seems to have corrected alot of issues,the XP carb is so much more responsive than the HP on the exact same engine with same jets and PV...
  23. Replies
    1
    Views
    911

    Just a follow up, i found out the info i needed,...

    Just a follow up, i found out the info i needed, it is referred to as a T-9 transmission and has a 2nd gear ratio of 1.81
  24. Replies
    6
    Views
    1,612

    Old Rob, i also sent you a PM on some lifter...

    Old Rob, i also sent you a PM on some lifter inserts
  25. Replies
    8
    Views
    1,478

    PM sent, for some reason when someone PM's me im...

    PM sent, for some reason when someone PM's me im not getting any email notification...anyone else having this issue?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

All times are GMT -5. The time now is 05:30 AM.


Powered by vBulletin® Version 4.2.0
Copyright © 2020 vBulletin Solutions, Inc. All rights reserved.