|
|
Search:
Type: Posts; User: twizted
Search:
Search took 1.51 seconds.
-
We were wondering how much HP gain you might see in a 350Hp engine going from Muncie 3 speed and stock clutch to a direct drive type trans like a Bert? Also how much HP it takes to turn a Quickchange...
-
Ok let me say I posted this as a joke not to make fun of Stock Car. I also will say I have a lot of respect for his ideas. I also want to know why people are commenting on my profile or private...
-
I'm not close enough friends with Jeff to post this but i guess he can throw me under the bus. It is in good humor man.
-
If you remeber 5-6 years ago on here Stock Car was preaching a balanced setup that few people ran and most bashed him over. I got a baseline of that setup and made it work on my car.
-
-
I want to sell this dyno. Over $5k invested. Maxwell industries peak force shock dyno for sale. Four speeds (1",3",6",12"/sec) with digital readouts for comp and reb. No computer needed. 120v, good...
-
Line size will not control final realized pressure at the pad. A small brake line that is to small will act as an orifice to restrict flow but will build the same final pressure. If you use a 1"...
-
Not being a butt hole but line size is part of the confined space and flow may be dictated through line size but not Pressure.
Pascal's law or the principle of transmission of fluid-pressure is a...
-
Thats what I thought but when we pulled the old out it was 1/4? Just had me wondering?
-
We are running new brake lines to the back of mu buddies car. Using reverse mount pedals and camaro calipers. Does he need 1/4" or 3/16 line from master to tee? Sorry if this is a stupid question but...
-
We just switched to a floater and the housing doesn't have drain or fill holes. We bought some bungs but don't know where to weld them in line with axle? Also we were ordering inner axle seals and...
-
On a leaf spring Camaro I need to know how much travel before driveshaft bottoms out in trans is needed? I have one shaft that only has 1/2-3/4" before bottoming out and another that has 2 plus but...
-
Thanks that's what I was just wondering. I have a high speed deburring tool that cuts pretty good and should work well. Thanks for you help I was thinking to much and couldn't see the simple answer. ...
-
That just made sense! The books list a 9/16 and a 5/8" thread for the two ball joints. I never thought the hole was to small. thanks for your help gonna try this the next time we are over there just...
-
Ok I been helping a (no computer savy) buddy try to put this metric clip modified together. question is car currently has the k6141 lower ball joints and B body spindles and he is thinking about...
-
My buddy bought this old modified that has a stock looking tie rod sleeve but it has 5/8 on one end and 11/16 on the other. One of them was missing when he picked the car up. The clip is a Metric...
-
-
-
If I don't find something will get back to you
-
Looking for 6.66 or 6.20 gear 31 spline center section or similar gear for ford 9". I really want to find a good used chunk to drop in but might think about just a gear at a really good price. Thanks
-
Deleted some messages, I will be glad to pay your fuel for every mile you save me off a 10 hour trip.
-
I have a chance to trade a old 4 wheeler we don't use anymore for a 602 crate motor that was in a buddies car when he bought it late this year and just wanted to run his built motor next year. We...
-
Sent you a text about gear
-
I am looking for a complete ford 9"chunk with a 6.66 gear for 31 spline axles. If you have anything would you please PM me with info.
-
I am looking for a complete ford 9"chunk with a 6.66 gear for 31 spline axles. If you have anything would you please PM me with info.
All times are GMT -5. The time now is 08:05 PM.
|
|