|
|
Search:
Type: Posts; User: StuckInReverse
Search:
Search took 0.41 seconds.
-
What about Trayvon's right to stand his ground? He was being followed (stalked) for no reason. How far would you let someone follow you before you confronted them? I'd wager a guess half the people...
-
Around 1 to 1-1/2" of rake is the only thing I've every measured on the frame rails. Never compared left to right as a setup basis. You would have to know if the rails are in the same plane or not,...
-
The guy who rebuilt our last one recommended Type-F. We had 7 seasons on the trans when we sold that car, and never had any issues.
There is an article with Mr. Brinn himself, where he basically...
-
So where exactly does that say he is a police officer? He had no right to confront, stop, or question Martin. Even the 911 operator told him to back off. Instead he followed (stalked) Martin which...
-
So it's okay to conceal a weapon, pick a fight, then shoot the guy when he starts beating your a$$?
-
Like Racer Roy said, the timing lines are in different places 305 vs 350. A lot of 305 balancers have the timing mark 10 degrees before the keyway on the crank. This may account for your timing...
-
You're 100% right keeks. According to what I found, a Brinn is 6.040" deep and a Bert/Falcon is 6.290" deep.
If I were going to fix this on the low budget, I would get a second .250" thick alum...
-
I've run a Brinn trans with a Bert flywheel and housing for years without issue.
What trans are you using, keeks?
-
I'll never understand this. It's not the cookie-cutter tracks or outdated rules that matter. It's the level of competition, and that's where NASCAR excels, even over Formula 1, or any other...
-
If you are truly bottoming out the oil pan, it will be obvious. The sump will be crumpled and covered in mud. If it's not, look at something else. Perhaps the RF lower control arm is hitting the...
-
Sounds like an cracked header or bad header gasket. Probably just a coincidence that it occurred the same week you adjusted valves.
-
Use some Loctite or run a stud girdle, if the rules allow.
-
Listen to Matt's advice. It's the most straight-forward method for finding the issue!
-
It really depends if you have someone knowledgeable helping out. If you don't have experienced help, I would suggest looking for something more complete.
-
Did you replace the tailshaft bushing as well? If it's damaged or missing, the extra slop will ruin the rear seal in a hurry.
-
This is mid-day in Beijing, China:
http://imgur.com/a/CnXGL
This is what the majority of our cities would look like with no emission or pollution regulations on industry.
I'll keep my EPA,...
-
The Constitution gives you the right to own guns.
It does not give you the right to secretly own guns.
It's amazing that the same people who worry about the 'big bad gubermit' knowing which...
-
It also depends on the number of stages you are running. When we ran a 3-stage, there wasn't a return on the heads or lifter valley, so we tie wrapped rags around the breathers and never had an issue.
-
Yeah, Keselowski was the one who was blocked in both cases. I don't put fault on him. Both Smith and Edwards moved in reaction to Keseslowki moving. I don't care for Brad, but at all, but not his...
-
...go Ravens! And see you boys back here on Monday! http://www.4m.net/images/smilies/cool.png
-
If that was the case Darwin, let's just recall all those assault weapons from are soldiers and give them revolvers.
Since, as you clearly indicate, they do equivalent damage.
-
No. You can't do more damage with a 6- or 7- round revolver that you can with a 30+ clip in an assault weapon.
Did you really just try to justify that? If you can't do more damage with an assault...
-
Sad facts, or lack thereof?
-
So I guess that's my answer? No logic or thoughtful reply, just an insult. I'll say it again: grow up, bud!
-
That's some nice copy & paste handiwork. I'm sure I could find a satirical matching version aimed at republicans. But who cares?? Let's see you argue your own thoughts with logic, rather than...
All times are GMT -5. The time now is 07:50 PM.
|
|