|
|
Search:
Type: Posts; User: jatchis
Search:
Search took 1.25 seconds.
-
(If this board offered an option to delete threads you started, I would have done so when I listed these parts elsewhere)
-
Ya know, I put these out here, watched religiously for a couple of weeks, saw there were no views on the thread, no replies, no personal messages, nothing. So listed the same parts at other sites....
-
You have Voice Mail ... ;-)
-
I have one, and can make you a good deal, but shipping costs may be prohibitive .....
-
.060 over block, casting D8EE (large journal, 2 piece rear main seal), tanked, magnafluxed, sonic checked for cylinder wall thickness and integrity, bored 60 over, align bored, and decked - $400
...
-
Not sure about the '97 ... the one we use is from the 91 - 96 Escort 1.9L. It weighs just over 16 pounds (we have a 16 pound minimum rule). Works with stock pressure plate and disk, but does require...
-
Do the transmissions have shifters or bellhousings with them?
-
You can still do the "spin test" with the tranny in the car, but it's a little more work ...
Jack the rear end up so the rear wheels are off the ground, and put a couple jack stands under the...
-
Check your fuel pick-up line inside the tank. I've seen this symptom a few times caused by a crack in the hose used for that pick-up. As the fuel sloshes through the corner, or the level is lowered...
-
Escort flywheel (91 – 96 1.9L):
http://www.rockauto.com/catalog/catalog.php?carcode=1119147&parttype=5348
NAPA p/n NNC 50708
Throw out bearing (72 Chevy C10 w/250CID, 3 spd., diaphragm type)...
-
Get the right side front lower control arm from a 93-95 Mustang. It's about 3/4" longer than the stock one.
Take the control arms off your rear-end, and grind all the "teeth" off the ends of the...
-
You would be amazed at how much difference an extra 1/2 to 1 pound of pressure in the right rear will loosen a car up when the track goes dry slick.
-
Look up inside the fitting ... it's a hex hole. It's a large hex, and I didn't have an allen wrench that size. But I did have a large punch who's handle was the right size, and put a box wrench on...
-
Try this ...
http://www.junkyardgenius.com/ignition/jeep/HEI01.html
-
We get them completely out from under the hood, so we get ambient air, rather than the hotter, under the hood air. We just get a cheap CalCustom, or Mr Gasket velocity stack, cut a 14" base so it has...
-
We run standard paper 14x3 filters, with Moroso foam pre-filter.
-
If you have a 23 spline tranny, then like Old Rob said, use the disc off a 71-72 Pinto with a 1600cc and German transmission. Use the pressure plate from a 91-96 Escort with the 1.9L ... it will bolt...
-
Good to see your "font" again, Joe!
Been worried about ya.
-
Folks that have been here a while, through all the iterations of this board, for the most part understand and appreciate the evolution of the character that is boportt.
Dude cracks me up, and if...
-
You should see his fan .....
-
Can you provide a little more detail on the head? Has there been any port work done on it? How many races since the build? Any specs on the cam?
-
OK, this really is weird, that 2 cars show to be off that much, and by about the same amount. There HAS to be something common, here.
By any chance, is it the same timing light you used the night...
-
A little food for thought here, mainly because the physics just don't seem to add up.
Here's a pic of a spare Esslinger pulley I had in the garage (sorry for the poor quality ... phone cam). In a...
-
We had similar issues the first time we installed a Big E pulley. I let myself get good and frustrated trying to figure out why they marked it where they did (we didn't have their pointer), and just...
-
http://www.rockauto.com has them for $0.77 each
ATP part #ZX104
All times are GMT -5. The time now is 11:52 AM.
|
|