|
|
Search:
Type: Posts; User: leadorfollow
Search:
Search took 0.21 seconds.
-
2016 Lazer Roller with DMI Bulldog rear. Wehr's Birdcages, starter and Winters Bell housing, 17 shows on car. Never bent or repaired. Comes with spare white doors, quarters and fender side panels. 4...
-
It depends how your car is made body wise. Measure the widest part of your body (usually where left side door sticks out or at rear of nose flares). Our car wouldn't fit through that opening either...
-
if you can't feel the vibration in the seat it's not the drive shaft. Your teeth will hurt all week long if a drive shaft is bent. It may be the yoke could be bent to wish is working them loose. ...
-
it all depends on the track is made of in all honesty. a 1400 needs a track with traction but not dry slick, a standard 1425 needs heat and keep it hot. never ever let it get cold or it'll seal...
-
we wipe the inside of the wheel down with wd40 before every race. no problems at all since we did this.
-
the non beadlock with tabs are the most hateful. The normal non beadlocks are super easy to mount. We don't use anything but air to mount ours so not sure if anything you might be using is causing...
-
we start the night on a 3 on rebound and change to a 5 rebound once the track blows off. If it goes absolutely dead slick and I mean lock down on the bottom of the track we'll go to a 7 but that's...
-
integra ida's. no canister required!
-
needling is mainly used where siping is not allowed or when treating tires to allow the chemical access to the rubber
-
https://www.bernheiselracecars.com/store.php?cid=10
the kool air box is in the top right and the hood scoop are on the bottom left. both are fiberglass. the box comes in black or white and the...
-
BRC sells a Kool Air box with hood scoop. That's what we have on our car and it works very well
-
can you send pics to ksprecher@embarqmail.com Where are you located? extra height?
-
we've toasted everything on the front end of our car this year except the ball joints. uppers and lowers. we went with the qa1's as well and they are rebuildable if you do decide to go that route. ...
-
one other alternative we have done is to either put more gas pressure in the lrf shock which wants to do the same as put more rebound in the rf and keeps it tied down more. Also you could simply put...
-
8 lb should be fine but you may want to check your floats and needles to make sure nothing is stuck or the secondaries to make sure it's not stuck open a little. Does it clear out on the track or...
-
a lot depends what type of clay/dirt/soil/sand/rock you're running on because some of the tires needs a lot of friction to make the tire work, some need wet moisture, some like abrasion and some...
-
when you say the car will not rotate on entry is that on the gas or off the gas? on the brake or off the brake? Where are your 4 bars at? what size track? what spring do you have on the right front?
-
since you're running the wrs55 there is no problem with flipping them since it's a hard tire and you're running off the edges. Just as was stated make sure you originally mount with date stamp...
-
I would recommend sitting in each brand seat before buying if possible. Our drive liked the feel of the butlerbuilt full containment seat and it is very well built. Find what's comfortable to you...
-
by full set do you mean all 6 shocks? is the rf a high rebound shock? When was the last time the were gone over and do they include coil over kits? thank you. Kyle
-
Can you please send pictures to ksprecher@embarqmail.com and can you please show pictures of tire racks. Thank you. Kyle
-
-
Thank you everybody for your information. Everything that I found had lead me to the conclusion that needling is only used to release heat. Depending how you sipe will either gain heat or release...
-
we ran all year last year on ours. we tore them apart here in the off season and they're ready for another season
-
we used the qa1 ball joints all last year. absolutely love them. The only downside is they don't come with a rubber boot to keep dirt out. Can't beat the price and if you have a local dealer then...
All times are GMT -5. The time now is 03:20 PM.
|
|