|
|
Search:
Type: Posts; User: north louisiana dirt
Search:
Search took 0.20 seconds.
-
The Frame deal has popped up again at the Usmts Mod race in Louisiana this Sat night..... can someone explain the 7.5 inch frame height rule as they go through tech ? The same car won Thursday night...
-
Mr. Flat Tire: I guess I am a little confused.... when I say "lower ratio" .... I think like going from a 567 (high) to a 668 (lower)... when I say "higher ratio" .... I think like going from a 668...
-
yeah, ok.. :-) .. So if your going to stay Legal, I was thinking more along the lines of lower gear ratio, speed through the center and exit in the slick vs the theory of high gear ratios in the...
-
looking for some discussion on " wheel speed" in dirt racing..... what is it and how it is applied?
-
thanks Billet and MB Racer.... I almost confused myself as one Mod I help is on a slider and one is on a wedge bolt...(rules).... so on the slider... what is the advantage of running a 13"-175# on...
-
I know this is a Late Model page, but the mod page seems dead at the moment....And I am no expert at all..... so as far as spring table is concerned... why would a Modified set up sheet call for a...
-
Mods are coming back next year.... so a buddy has a grt with g15 welded on the rear frame... looking for some starting points.... found some generic set up sheets at grt but don't show a G15.....car...
-
is there a simple way to measure the carb to figure out venturi size and cfm with the E85 specialty carbs that don't have list numbers anywhere on them....
-
thank you Sir... we are working up a plan to address these issues.... I took the carb apart today and did not see any obvious generic issues... I have never used a belt drive pump with a check valve...
-
directly from the driver...>>>>>>>>>>>>>>>..Sure. During the feature, when I run the bottom and drive off into the corner, and go to pick up the throttle at the 1/4 mark or so of the corner, the car...
-
I will have to get with the driver and get more detail for you...... and pinpoint exactly what is going on.... It looks like, from where I was hanging in the fence... it would rotate on entry and...
-
we have an older (2015) mastersbilt and have been told to raise the motor 1.250 inches in the car for the crate motor. Should we tilt it a few degrees down in the back and a few degrees to the left...
-
yes Sir, we raised and lowered the float level , raising it seemed to make it worse, lowering it helped a little... driver "thinks" it's carrying 6psi fuel pressure down the straights , but not for...
-
we are trying to sort out a similar problem with our 604 crate LM.... the WRC /aeromotive mech drive pump Part number is 250250LM..... does that mean it is a 250 size or 250 gph pump ? car was...
-
the generic set up sheet they sent me just says 14.5 L bar and 15.5 U bar.... 3rd hole up B, 5 hole up U bar... both sides...... seems like you should also check index with angle finder to double...
-
The Guy I help traded a Mod for a Late model (2014 Mastersbilt) and we are trying Crate Late racing for the first time. First Late Model. Car needs body and some deck. While it is stripped down this...
-
would this be an adjustment for when the track rubbers up a bit in the feature and you get a little push on exit ? What is the ratio of Hike vs rear steer and what is more prevalent at the exit of...
-
what's your LS % and Rear %.?... remember , everything you do to make a car turn on entry and in the middle are all band aids if the LS % is too low.... most people never get a car loose enough to...
-
Banana: you need to go whole hog and go to the extended LR spring deal.... we are on a 16" long 85# LR spring...set it 1.25" pre load at full hike...jack it up, put it on the chain, take a tape...
-
Thanks racer 69.... can't ever stop working on the "science project" of suspension.... can't.... we have an added problem that makes you stay on top of it.... we can't just throw a new set of sticker...
-
Banana: I started with a 500 last Fri.... I am borrowing a 400 tomorrow and will put it on a spring checker and see how much I can smash it before I get into a coil bind issue.... Pre load is the...
-
march 2020 page 98 and 99
-
march 2020 dirtmonthly mag has a mark bush article you need to read.... all your answers in there.... go to dirtmonthly.com for free down load.. they are free now because they can't print/ship........
-
we run a class of open wheel mods that don't run a roof.... body rules are very general, mostly IMCA type or close... max rear deck height, width, etc.. I'm an old school guy that for years, thought...
-
I am by no means an expert... but just thinking about why and how you race these cars ........if your fast, it would establish a baseline for future adjustments... minor tweaks to improve... if your...
All times are GMT -5. The time now is 09:53 PM.
|
|