Search:

Type: Posts; User: Lizardracing

Page 1 of 20 1 2 3 4

Search: Search took 3.17 seconds.

  1. Replies
    5
    Views
    342

    Ships in a week from today...

    Ships in a week from today
    https://www.jegs.com/i/Dart/301/10510020P/10002/-1#
  2. Replies
    10
    Views
    900

    Correct, Making the hole bigger, means the...

    Correct,
    Making the hole bigger, means the stud/pin will go further into the hole.
  3. Replies
    12
    Views
    1,150

    Braided lines are plastic too with a SS outer...

    Braided lines are plastic too with a SS outer fabric.
    I do plastic, change it every couple years. Be smart where you run it and tie it down well and it's never been an issue for me.
  4. Replies
    10
    Views
    900

    Wait a minute, the 1210-102 is a 10' stud, not 7...

    Wait a minute, the 1210-102 is a 10' stud, not 7 degree. 3.848 long
  5. Replies
    10
    Views
    900

    I don't mess with Cotter keys. BUT....I also...

    I don't mess with Cotter keys. BUT....I also check them every week as part of the maintenance. If you have full thread engagement of the castle nut, and you like the car as is, just check them every...
  6. Replies
    4
    Views
    576

    Dart had me on the A8

    Dart had me on the A8
  7. Replies
    7
    Views
    645

    depending the MC you are using, I have an old one...

    depending the MC you are using, I have an old one I drilled a 9/16 hole in it, fitted a tire valve, Then use a locking air chuck and apply 20psi to the MC, crawl under the car and open the bleeder....
  8. Replies
    7
    Views
    645

    I put a 1/4" rubber vacuum line over the bleeder...

    I put a 1/4" rubber vacuum line over the bleeder screw and crack it open a 1/2 turn. Stick the other end of the hose into a container with enough fluid to cover the end of the hose by about an inch. ...
  9. Replies
    4
    Views
    576

    What head?

    What head?
  10. Replies
    2
    Views
    641

    Think about where the bar is applying the loads...

    Think about where the bar is applying the loads from the chassis.
    Moving the bar from the RS of the pinion to the middle moves the loads about 1.5" closer to the LR.
    So all things the same, it'll...
  11. Replies
    10
    Views
    1,160

    I talked to a local track about renting for a day...

    I talked to a local track about renting for a day and they told me $1000 dollars.
    That plus fuel and tires and all that made it out of reach. I was better off doing the testing during normal nights...
  12. Replies
    9
    Views
    1,596

    Ask for dyno sheets, If they can't produce them...

    Ask for dyno sheets, If they can't produce them and are current assume they need rebuilt and add that to the cost of the deal and compare to buying new. Around here people are stupid with pricing on...
  13. Replies
    3
    Views
    1,012

    You have to call them first to get an RA number....

    You have to call them first to get an RA number. You track it through the process with the RA number so make sure it's clearly seen and can't rub off or anything because they won't know where it's...
  14. Replies
    5
    Views
    1,282

    Chad hang outs on Hotrodders, Yellowbullet and...

    Chad hang outs on Hotrodders, Yellowbullet and Speedtalk often.
    All are online forums.
  15. Thread: E85

    by Lizardracing
    Replies
    4
    Views
    1,196

    Everything a person needs to know right here. ...

    Everything a person needs to know right here.
    https://afdc.energy.gov/fuels/ethanol_production.html

    Most E85 pumps around here, as most are now, are blender pumps. Blender pumps are pump that...
  16. Thread: E85

    by Lizardracing
    Replies
    4
    Views
    1,196

    I buy from a local station that refills weekly....

    I buy from a local station that refills weekly. It's a blender pump station. I always use the same pump. It's always right at 70 percent. I bought a gallon for testing at another station down the...
  17. Thread: Starters?

    by Lizardracing
    Replies
    23
    Views
    4,209

    On this topic I bought my QM from a guy, that was...

    On this topic I bought my QM from a guy, that was his spare and not used. I had it apart a silly coned it shut, sealing off water/dirt. It's been great too me for 10 years.
  18. Howe and QA1 have it listed on the web sites by...

    Howe and QA1 have it listed on the web sites by dimension. You can also download the catologue and dig through it or measure yours and call them. QA1 has great support. I don't buy Howe so I can't...
  19. Thread: corrosion

    by Lizardracing
    Replies
    6
    Views
    1,955

    Possible electrolysis. Make sure you have good...

    Possible electrolysis. Make sure you have good shiny clean electrical grounds and even adding the OEM braided strap from engine to chassis is NEVER a bad idea.
  20. Thread: Starters?

    by Lizardracing
    Replies
    23
    Views
    4,209

    Maybe helpful I don't know But I use AWG 2...

    Maybe helpful I don't know But I use AWG 2 welding ground cable(stranded) and solder the ends on. I use Dialectric grease on all the connections. I check the frame grounds for shiny metal several...
  21. Replies
    15
    Views
    1,901

    Well, this was real handy last week. The radiator...

    Well, this was real handy last week. The radiator cap is bad and the engine slowly lost it water. The pressure light came on the last lap but the gauge never left 210. At home, the radiator was only...
  22. Replies
    5
    Views
    1,273

    20 percent or more isn't unusual on a .030 GM...

    20 percent or more isn't unusual on a .030 GM block if it's not been honed with a torque plate. I'd send it.
    A teaspoon of engine oil in the cylinders can tell you a lot about the rings. If the...
  23. Replies
    19
    Views
    2,359

    Optimum front end will depend mostly on driving...

    Optimum front end will depend mostly on driving style and what you want the back end to do. Think total combination.
  24. Thread: Side bite

    by Lizardracing
    Replies
    8
    Views
    1,837

    I went to a MLRA event last week and the winner...

    I went to a MLRA event last week and the winner drove the car turning left most of the time. I'm sure the RR was bald a baby's butt but he also won against the top three blowing RR tires. 5 RR's...
  25. Replies
    17
    Views
    2,107

    I was the tech guy for two local tracks. Both UMP...

    I was the tech guy for two local tracks. Both UMP at the time. Niether liked my style nor did UMP so that ended and I went back to racing my own car.
    I know of matter of personal experiance,...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

All times are GMT -5. The time now is 08:22 AM.


Powered by vBulletin® Version 4.2.0
Copyright © 2021 vBulletin Solutions, Inc. All rights reserved.