Search:

Type: Posts; User: billy5

Page 1 of 3 1 2 3

Search: Search took 0.38 seconds.

  1. Thread: stagger

    by billy5
    Replies
    8
    Views
    4,661

    if you cant turn thru the corners...add more...

    if you cant turn thru the corners...add more stagger...if it steps out coming out of the corner then reduce stagger....quit listening to others and fiqure out what works for you with what you have..
  2. Replies
    25
    Views
    16,665

    i made all of mine...3'' id pipe cut in half and...

    i made all of mine...3'' id pipe cut in half and rewelded aroung the rearend tube...cut 1/2'' wide rings and welded to rearend on each side of floater to hold the side to side,then welded spring...
  3. Replies
    25
    Views
    16,665

    keep reading the outdated stuff ....it hasnt...

    keep reading the outdated stuff ....it hasnt changed much..i have tried it and can say that it can be a handfull to fiqure out....very small moves make a world of differnce...its easy to go from...
  4. Replies
    3
    Views
    1,594

    60in rear is a common sized ford rear......you...

    60in rear is a common sized ford rear......you can allways make up the difference with wheel offset
  5. Replies
    25
    Views
    16,665

    i just read you had found left floaters...didnt...

    i just read you had found left floaters...didnt mean to stir anything....its something you have to fiqure out how to make it work for your own driving style and for the track you race at....if you...
  6. Replies
    25
    Views
    16,665

    floater goes on right rear.

    floater goes on right rear.
  7. Replies
    3
    Views
    1,061

    same as ar kk704

    same as ar kk704
  8. Replies
    5
    Views
    3,012

    just about ant full bodied gm car parts work....

    just about ant full bodied gm car parts work....
  9. Thread: Need Help

    by billy5
    Replies
    7
    Views
    2,749

    set a whole lot of engine about 12" behind it

    set a whole lot of engine about 12" behind it
  10. Replies
    1
    Views
    1,472

    i used a piece of 3 1/2" pipe cut longways and...

    i used a piece of 3 1/2" pipe cut longways and welded back together on the axle tube where its slightly loose ....its the same width as the lower spring plate.....drilled a hole in it and used a...
  11. Thread: chassis help

    by billy5
    Replies
    9
    Views
    2,849

    its camaro...........but the engine seems really...

    its camaro...........but the engine seems really low.
  12. Replies
    4
    Views
    2,989

    adding stagger...using a smaller lr tire will put...

    adding stagger...using a smaller lr tire will put more load on rr tire and tends to tighten entry but loosens exit if it spins the tires...knowing where the problem is on the track is important for...
  13. Thread: Need help fast

    by billy5
    Replies
    2
    Views
    1,282

    probably to much duration for the...

    probably to much duration for the compression...it will kill all the low end torque...common mistake is to get a too big of cam...
  14. Replies
    1
    Views
    803

    1st gear is 2.52,,,,,,2cnd gear is 1.52..........

    1st gear is 2.52,,,,,,2cnd gear is 1.52....... gear you race in times rearend ratio = final drive.....example..1.52 x 4.56 = 6.93
  15. 1978 thru 1988

    1978 thru 1988
  16. Replies
    15
    Views
    2,108

    running lean will make them pop thru thr carb

    running lean will make them pop thru thr carb
  17. Replies
    15
    Views
    2,108

    likely a flat cam if its a fresh build and you...

    likely a flat cam if its a fresh build and you didnt use breakin oil..
  18. explain please

    explain please
  19. Thread: roll centers

    by billy5
    Replies
    7
    Views
    2,725

    explain please

    explain please
  20. Thread: Cam ?

    by billy5
    Replies
    7
    Views
    2,564

    yes...they say you cant.....but dirt racers do it...

    yes...they say you cant.....but dirt racers do it all the time......buy good ones if the spring pressures are high..
  21. Replies
    1
    Views
    1,856

    rear metric angles

    metric dirt streetstock....sandy/slick..med banked 1/4 mile...if i could change the angles of the upper rear arms,what would be idea angles?? im trying to get more fwd drive without moving weight way...
  22. Thread: over heating

    by billy5
    Replies
    16
    Views
    2,270

    big cam,,,,intake reversion...intake manifold vs...

    big cam,,,,intake reversion...intake manifold vs exhaust design.....lots of variables at part throttle no load...never done a egt test not without it being loaded so not sure.....
  23. Thread: over heating

    by billy5
    Replies
    16
    Views
    2,270

    egts at wide open throttle should be close to...

    egts at wide open throttle should be close to 1000deg. sounds rich or retarded timing...
  24. Replies
    6
    Views
    1,042

    timing retard

    sounds crazy i know...but...i had a flat tappet hydraulic cam engine that i installed a high pressure oil pump in and it started doing the same thing with oil pressure close to 80 psi....was told the...
  25. Thread: over heating

    by billy5
    Replies
    16
    Views
    2,270

    30 degs timing may be to low causing overheating...

    30 degs timing may be to low causing overheating and hot exhaust temps..
Results 1 to 25 of 60
Page 1 of 3 1 2 3

All times are GMT -5. The time now is 06:52 AM.


Powered by vBulletin® Version 4.2.0
Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.