Search:

Type: Posts; User: twizted

Page 1 of 4 1 2 3 4

Search: Search took 0.98 seconds.

  1. Replies
    10
    Views
    2,420

    Hp gain going to Bert and loss through QC

    We were wondering how much HP gain you might see in a 350Hp engine going from Muncie 3 speed and stock clutch to a direct drive type trans like a Bert? Also how much HP it takes to turn a Quickchange...
  2. Replies
    31
    Views
    11,813

    Ok let me say I posted this as a joke not to make...

    Ok let me say I posted this as a joke not to make fun of Stock Car. I also will say I have a lot of respect for his ideas. I also want to know why people are commenting on my profile or private...
  3. Replies
    31
    Views
    11,813

    I'm not close enough friends with Jeff to post...

    I'm not close enough friends with Jeff to post this but i guess he can throw me under the bus. It is in good humor man.
  4. Replies
    31
    Views
    11,813

    If you remeber 5-6 years ago on here Stock Car...

    If you remeber 5-6 years ago on here Stock Car was preaching a balanced setup that few people ran and most bashed him over. I got a baseline of that setup and made it work on my car.
  5. Replies
    31
    Views
    11,813

    Stock Car

    Deleted post
  6. Replies
    4
    Views
    1,803

    I want to sell this dyno. Over $5k invested....

    I want to sell this dyno. Over $5k invested. Maxwell industries peak force shock dyno for sale. Four speeds (1",3",6",12"/sec) with digital readouts for comp and reb. No computer needed. 120v, good...
  7. Replies
    7
    Views
    2,281

    Line size will not control final realized...

    Line size will not control final realized pressure at the pad. A small brake line that is to small will act as an orifice to restrict flow but will build the same final pressure. If you use a 1"...
  8. Replies
    7
    Views
    2,281

    Not being a butt hole but line size is part of...

    Not being a butt hole but line size is part of the confined space and flow may be dictated through line size but not Pressure.
    Pascal's law or the principle of transmission of fluid-pressure is a...
  9. Replies
    2
    Views
    853

    Thats what I thought but when we pulled the old...

    Thats what I thought but when we pulled the old out it was 1/4? Just had me wondering?
  10. Replies
    2
    Views
    853

    Brake line size to rear 3/16 or 1/4?

    We are running new brake lines to the back of mu buddies car. Using reverse mount pedals and camaro calipers. Does he need 1/4" or 3/16 line from master to tee? Sorry if this is a stupid question but...
  11. Replies
    1
    Views
    589

    Ford 9" fill level and axle seal?

    We just switched to a floater and the housing doesn't have drain or fill holes. We bought some bungs but don't know where to weld them in line with axle? Also we were ordering inner axle seals and...
  12. Replies
    2
    Views
    1,183

    Driveshaft length/travel camaro

    On a leaf spring Camaro I need to know how much travel before driveshaft bottoms out in trans is needed? I have one shaft that only has 1/2-3/4" before bottoming out and another that has 2 plus but...
  13. Thread: Spindle taper

    by twizted
    Replies
    17
    Views
    2,820

    Thanks that's what I was just wondering. I have a...

    Thanks that's what I was just wondering. I have a high speed deburring tool that cuts pretty good and should work well. Thanks for you help I was thinking to much and couldn't see the simple answer. ...
  14. Thread: Spindle taper

    by twizted
    Replies
    17
    Views
    2,820

    That just made sense! The books list a 9/16 and a...

    That just made sense! The books list a 9/16 and a 5/8" thread for the two ball joints. I never thought the hole was to small. thanks for your help gonna try this the next time we are over there just...
  15. Thread: Spindle taper

    by twizted
    Replies
    17
    Views
    2,820

    Spindle taper

    Ok I been helping a (no computer savy) buddy try to put this metric clip modified together. question is car currently has the k6141 lower ball joints and B body spindles and he is thinking about...
  16. Replies
    2
    Views
    1,008

    5/8 x 11/16 tie rod sleeve

    My buddy bought this old modified that has a stock looking tie rod sleeve but it has 5/8 on one end and 11/16 on the other. One of them was missing when he picked the car up. The clip is a Metric...
  17. Replies
    0
    Views
    1,121

    found it in search thanks

    found answer in a search
  18. Sent you a pm oldtimer

    Sent you a pm oldtimer
  19. If I don't find something will get back to you

    If I don't find something will get back to you
  20. Looking for 6.66 or 6.20 gear 31 spline center section

    Looking for 6.66 or 6.20 gear 31 spline center section or similar gear for ford 9". I really want to find a good used chunk to drop in but might think about just a gear at a really good price. Thanks
  21. Replies
    8
    Views
    1,015

    Deleted some messages, I will be glad to pay your...

    Deleted some messages, I will be glad to pay your fuel for every mile you save me off a 10 hour trip.
  22. Replies
    0
    Views
    1,087

    602 crate motor power band and RPM limit?

    I have a chance to trade a old 4 wheeler we don't use anymore for a 602 crate motor that was in a buddies car when he bought it late this year and just wanted to run his built motor next year. We...
  23. Replies
    10
    Views
    1,749

    Sent you a text about gear

    Sent you a text about gear
  24. Replies
    0
    Views
    408

    Looking for ford 9" chunk with 6.66 gear

    I am looking for a complete ford 9"chunk with a 6.66 gear for 31 spline axles. If you have anything would you please PM me with info.
  25. Looking for a Ford 9" chunk with 6.66 gear

    I am looking for a complete ford 9"chunk with a 6.66 gear for 31 spline axles. If you have anything would you please PM me with info.
Results 1 to 25 of 83
Page 1 of 4 1 2 3 4

All times are GMT -5. The time now is 06:51 PM.


Powered by vBulletin® Version 4.2.0
Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.