Search:

Type: Posts; User: Fox_hunter42

Page 1 of 7 1 2 3 4

Search: Search took 2.18 seconds.

  1. Replies
    0
    Views
    1,003

    Falcon trans

    Our falcon late model trans the set screw for high/low gears fork keeps coming loose. I have used lock tight. What might cause that
  2. Replies
    9
    Views
    2,373

    good to know thanks

    good to know thanks
  3. Replies
    9
    Views
    2,373

    what happens to the coupler???

    what happens to the coupler???
  4. Replies
    9
    Views
    2,373

    bullitwrench, thanks they helps a lot

    bullitwrench, thanks they helps a lot
  5. Replies
    9
    Views
    2,373

    Falcon Trans

    Where can I find repair/rebuild info for a Falcon Trans?
  6. Replies
    4
    Views
    1,642

    He is telling us 110 race fuel. I don't doubt...

    He is telling us 110 race fuel. I don't doubt him, just didn't want to spend the money if it wasn't gong to help. We have been running good with pump premium, just trying to get a little more
  7. Replies
    4
    Views
    1,642

    602 crate and 4412

    What fuel is everyone running? race gas or pump premium?
  8. you don't mention cross %. I'm guessing with that...

    you don't mention cross %. I'm guessing with that much lr bite your cross is high
  9. Replies
    21
    Views
    6,252

    we have 2.5, 1.6, 200cc iron eagles on our 383....

    we have 2.5, 1.6, 200cc iron eagles on our 383. awesome combo
  10. Replies
    2
    Views
    823

    we run an Imod, last year was street stock with...

    we run an Imod, last year was street stock with 3/4 bolts on all 4 corners
  11. Replies
    5
    Views
    1,291

    in either gear it will eventually break the ears...

    in either gear it will eventually break the ears off inside the clutch paks. Other than that there will be no difference. If possible, gear for high gear, that is the most efficient gear on any...
  12. Replies
    6
    Views
    2,712

    hands down-VDL. awesome carb

    hands down-VDL. awesome carb
  13. Replies
    1
    Views
    628

    When you buy a vdl carb, they are built special...

    When you buy a vdl carb, they are built special for your motor. If you buy a used one it may not perform well for you. That being said, you can send it back to vdl with complete engine specs. They...
  14. Replies
    3
    Views
    1,083

    thanks brad, that's what I thought

    thanks brad, that's what I thought
  15. Replies
    3
    Views
    1,083

    Someone must have some knowledge

    Someone must have some knowledge
  16. Replies
    12
    Views
    1,572

    valves too tight?

    valves too tight?
  17. Replies
    3
    Views
    1,083

    602 exhaust

    Do the 602 motor prefer smaller tube and collector headers. We have 1 3/4 tube, 3 1/2 collector headers, would I benefit from mufflers
  18. Replies
    7
    Views
    1,376

    valves set to tight

    valves set to tight
  19. Replies
    4
    Views
    1,815

    we dont run a camaro, but on our 1/3 mile semi...

    we dont run a camaro, but on our 1/3 mile semi banked, we have 1 1/2 -2" in rear. Front around 1". wheels: lf 4, rf 2, rr 4. lr 2 or 3 depending on track
  20. Replies
    16
    Views
    2,316

    If starting with 7/8, what happens when car rolls...

    If starting with 7/8, what happens when car rolls over in corner. Bar angles will cause rear axle to move around. You maybe have a lot of rear when car rolls onto right side thru corner.

    Do your...
  21. Replies
    8
    Views
    1,375

    bird cage type spring/shock mount or clamped? If...

    bird cage type spring/shock mount or clamped? If I'm understanding, you jack up the right side of rear end, the left comes up too. If you move the rr spring or leave spring and remove shock the...
  22. Replies
    8
    Views
    1,375

    panhard bar holding it?, when I ran my 3 link i...

    panhard bar holding it?, when I ran my 3 link i had rr spring behind, shock in front. lr spring in front shock behind, progressive spring on pull bar with 15 degrees, j bar in hole on right side of...
  23. Replies
    6
    Views
    1,650

    I would back timing down under 36. Also you may...

    I would back timing down under 36. Also you may have to change pulleys or restrictor in thermostat housing
  24. Replies
    8
    Views
    1,375

    spring slider binding?, shock bent

    spring slider binding?, shock bent
  25. Replies
    14
    Views
    3,197

    hoosier has posted recommended pressures on their...

    hoosier has posted recommended pressures on their website. You will be amazed at what they suggest.
Results 1 to 25 of 172
Page 1 of 7 1 2 3 4

All times are GMT -5. The time now is 12:01 PM.


Powered by vBulletin® Version 4.2.0
Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.