Search:

Type: Posts; User: ace1

Page 1 of 7 1 2 3 4

Search: Search took 0.34 seconds.

  1. Thread: 602 Fuel

    by ace1
    Replies
    2
    Views
    277

    E85 is legal as of this year.

    E85 is legal as of this year.
  2. Thread: 602 Fuel

    by ace1
    Replies
    2
    Views
    277

    602 Fuel

    What fuel are you running in your 602? I have been using 110 race gas. Is it really any better than pump gas for these motors. I know pump is recommended from factory.
  3. Replies
    0
    Views
    643

    Mastersbilt Spindles

    What is the difference in the standard Mastersbilt Smackdown and S7 spindles. Are there markings or a way to measure and find out what I have?
  4. 1-2 years old. Marshall, TX. My dad raced there...

    1-2 years old. Marshall, TX. My dad raced there around 1964-1966
  5. Thread: RR shock angle

    by ace1
    Replies
    4
    Views
    2,212

    It looks to be added but might not be. The welds...

    It looks to be added but might not be. The welds don't look the same but they did a very good job. So moving inward will soften spring and add drive? I'm on non adjustable shocks. If I have the car...
  6. Thread: RR shock angle

    by ace1
    Replies
    4
    Views
    2,212

    RR shock angle

    I have a 08 Mastersbilt that has had a shock mount added to the chassis on the RR which will lean the shock more in toward center of car. What's the thoughts on moving it in? What would be more...
  7. Thread: DIY Tire machine

    by ace1
    Replies
    6
    Views
    1,975

    I saw one made from a small winch. They just used...

    I saw one made from a small winch. They just used the motor and rigged up a coupler. Mounted a battery on the stand and just used 12v.
  8. Replies
    0
    Views
    1,362

    Mastersbilt rear deck height

    08 mastersbilt. What is the height of the rear deck support. I know rules may have a lot to do with it. But if making a new rear deck support how long would you make the tube to the bumper. Iím not...
  9. Replies
    3
    Views
    2,002

    View Post

    36 1/2

    I donít know why I have to put 10 characters in the post.
  10. Replies
    3
    Views
    2,002

    Aluminum drive shaft?

    I donít see many if any aluminum drive shafts in my area. What are thoughts on these. Iím needing one and found a used one from a reputable source. Iíve only used steel in the past.
  11. Replies
    8
    Views
    2,102

    I have one of the wissota cars I'm getting...

    I have one of the wissota cars I'm getting together. Its a 08 I'm told, round tube 01370W. The engine is set back more. My son has a 08 square tube and I have to use a shorter drive shaft than his...
  12. Replies
    0
    Views
    1,354

    08 Mastersbilt Wissota setup? edited

    What are differences in the Wissota and Std. smackdown chassis? I have found the engine is set back different and the rear end doesn't set the same left to right. I have 17" instead of 15 3/4 from...
  13. Replies
    5
    Views
    2,063

    Is there any other differences on the wissota...

    Is there any other differences on the wissota cars. I was just checking the rear end side to side and it doesn't measure to the book spec.
  14. Replies
    5
    Views
    2,063

    That is it. It does have a W. I wondered about...

    That is it. It does have a W. I wondered about that. Thanks
  15. Replies
    5
    Views
    2,063

    17.5/15.5 both sides

    17.5/15.5 both sides
  16. Replies
    5
    Views
    2,063

    08 Mastersbilt drive shaft length

    We have 2 08 Mastersbilt cars, one square tube, one round tube. Standard slip yoke Bert trans in both. The square tube is using a 38" drive shaft but a 38 is too long for the round tube. It likes...
  17. Replies
    6
    Views
    2,426

    Oh no, I'm not. I found a crack in it around the...

    Oh no, I'm not. I found a crack in it around the starter cup any way. I'll keep my steel bell in for now. Thanks
  18. Replies
    6
    Views
    2,426

    I think that is the one I have. The hole is about...

    I think that is the one I have. The hole is about 5 1/8". But I don't have an adapter.
  19. Replies
    6
    Views
    2,426

    GM Aluminum Bell Housing

    Will a stock GM aluminum bell housing be ok for a crate car. I think it would be as good as the bert or brinn. Most of those have been cracked and repaired.
  20. Thread: LR Brake Floater?

    by ace1
    Replies
    15
    Views
    3,120

    Got it. Thanks

    Got it. Thanks
  21. Thread: LR Brake Floater?

    by ace1
    Replies
    15
    Views
    3,120

    Thanks for the tips and suggestions. I will give...

    Thanks for the tips and suggestions. I will give it a go, play around with it some and see what happens. I'm getting out of a 04 GRT and into the 08 Mastersbilt. Should I expect a big difference in...
  22. Thread: LR Brake Floater?

    by ace1
    Replies
    15
    Views
    3,120

    I won't have to worry about that where I'm at. I...

    I won't have to worry about that where I'm at. I could probably run one and get away with it. Once I find the position of the floater that works best, it will stay at that position when making bar...
  23. Thread: LR Brake Floater?

    by ace1
    Replies
    15
    Views
    3,120

    View Post

    Iím not sure what is on it but the left look good. The right were wore out.
  24. Thread: LR Brake Floater?

    by ace1
    Replies
    15
    Views
    3,120

    Thanks. I think I will leave it hooked up and try...

    Thanks. I think I will leave it hooked up and try it. I don't know why I thought I was loosing one of the adjustment holes on the frame.
  25. Thread: LR Brake Floater?

    by ace1
    Replies
    15
    Views
    3,120

    This car has the large hole brackets and I wasn't...

    This car has the large hole brackets and I wasn't sure if I would like not having one hole for bar adjustment. I may leave everything set up so I can unlock it and try it. It is a bearing type...
Results 1 to 25 of 162
Page 1 of 7 1 2 3 4

All times are GMT -5. The time now is 10:54 PM.


Powered by vBulletin® Version 4.2.0
Copyright © 2022 vBulletin Solutions, Inc. All rights reserved.