Search:

Type: Posts; User: DaveBauerSS6

Page 1 of 20 1 2 3 4

Search: Search took 2.08 seconds.

  1. Replies
    2
    Views
    1,496

    Put in shorter springs.

    Put in shorter springs.
  2. Replies
    4
    Views
    1,469

    Get some EQ heads with good valvetrain parts....

    Get some EQ heads with good valvetrain parts. Good 350 short block, spend a little more money for insurance/ longevity. Several cam mfg know the IMCA combo, Bullet seems to be easy to talk to.
  3. Replies
    1
    Views
    781

    The TCi s Ive opened up have only 2 reverse...

    The TCi s Ive opened up have only 2 reverse clutches. Shifting into reverse at higher than idle speed will break them. Shifting into reverse while moving forward will break the clutches. You have to...
  4. Replies
    10
    Views
    2,774

    Why would you want 62% cross? Is this a dirt car??

    Why would you want 62% cross? Is this a dirt car??
  5. Replies
    19
    Views
    4,563

    Excuse the hijack, BUT that's the baddest stock...

    Excuse the hijack, BUT that's the baddest stock car I've seen in a long time. Carry on.
  6. Hitler saves IMCA Stock Cars in California

    https://www.facebook.com/Imcastockcarsca/

    On our Stock car Page.
  7. Replies
    2
    Views
    1,686

    Get the TCI and move on.

    Get the TCI and move on.
  8. Replies
    4
    Views
    1,412

    Get the moly. They are new so the clearances are...

    Get the moly. They are new so the clearances are tight on the seal rings, no wear on the bushing area and they are strong. Get the 350 spline. Never worry about it again.
  9. Replies
    1
    Views
    1,492

    Ask Jeff that has won with these angles. ...

    Ask Jeff that has won with these angles.

    http://www.jnjfab.com/gallery/gallery.asp?id=44
  10. Replies
    6
    Views
    2,282

    JNJ has the calipers mounted so they will not...

    JNJ has the calipers mounted so they will not hit.
    60 inch with long studs will allow you to run 3 offsets .
  11. Replies
    5
    Views
    2,563

    And how tight are the bolts?

    And how tight are the bolts?
  12. Replies
    3
    Views
    1,902

    How much do you have now and how much more do you...

    How much do you have now and how much more do you want?
  13. Replies
    6
    Views
    2,282

    They will not hit if mounted right....

    They will not hit if mounted right.
    http://www.jnjfab.com/gallery/gallery.asp?id=44
    Take this short cut. It works,
  14. Replies
    113
    Views
    30,014

    The Pendulum will swing back to the open motor. ...

    The Pendulum will swing back to the open motor. IMCA sport Mods softened the A Mod counts in Cali. Everyone but the hard core no crate guys are running well on the crate and enjoying it. The low...
  15. Replies
    10
    Views
    1,852

    u joint bad?

    u joint bad?
  16. Replies
    21
    Views
    6,513

    Change the RR to 200. Dont use the spacer on the...

    Change the RR to 200.
    Dont use the spacer on the RF.
    Scale the car and get at least 100# bite on LR and 40# bite on LF
  17. Replies
    19
    Views
    3,747

    If you won a month ago,at the same track, with...

    If you won a month ago,at the same track, with the same driver,why would you change to a z bar? Something in the car changed. Verify all the shocks are good, check for bind at all pivot points, front...
  18. Replies
    6
    Views
    1,072

    Is there a gear ratio rule. Is there a RPM chip...

    Is there a gear ratio rule.
    Is there a RPM chip rule?
  19. Replies
    7
    Views
    3,104

    Swap the front shocks. Add 1 inch plus to the...

    Swap the front shocks.
    Add 1 inch plus to the rear stagger.
    Last I would coach the driver to set the car earlier in the entry,the drier the track gets
  20. Replies
    8
    Views
    1,986

    Float level too low. Main bleed dirty/...

    Float level too low.
    Main bleed dirty/ restricted.
    Power valve stuck closed.
    Incorrect metering block gasket.
  21. Replies
    9
    Views
    2,167

    You will bend the mono on the left floating it. ...

    You will bend the mono on the left floating it.

    Scrap the mono and the coil and go to a stacked leaf on the LR, no lift bar.

    Or

    Mono and float both sides and run the lift bar.
  22. Replies
    9
    Views
    1,937

    Lock out the mechanical advance in the...

    Lock out the mechanical advance in the distributor.
  23. Replies
    18
    Views
    3,776

    I would put a NEW pair of 200 springs for the...

    I would put a NEW pair of 200 springs for the rear. And get 2-3 inch stagger for the rear. Leafs don't like 100+ bite. Tune the roll with the LF shock.
  24. Replies
    7
    Views
    1,643

    May consider mounting the panhard bar on the...

    May consider mounting the panhard bar on the right side frame rail, but below the center line of the axle. This was discussed in the Larry Shaw Class. Issues with ground clearance and mounting...
  25. Replies
    8
    Views
    2,012

    Napa 30 amp push pull.No more problems. Info...

    Napa 30 amp push pull.No more problems.
    Info compliments of Larry Shaw school.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

All times are GMT -5. The time now is 11:34 AM.


Powered by vBulletin® Version 4.2.0
Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.