|
|
Search:
Type: Posts; User: racer21
Search:
Search took 0.58 seconds.
-
Helping a friend put a car together he has to buy a rear and we are trying to decide if he should go with a 60 centered or the 2in offset. Pro's and con's of each would be greatly helpful Thank You...
-
Ok guys the way I done it was install two straight wheels set it up on blocks and spin the rearend,not sure if this is correct but the wheels move in and out,now for the good part I got the second...
-
Wondering what kinda angle people try to acheve on the rear uppers,i have to put new mts on top and was wondering if I should put more angle in the bars or less? Anyone know?
Pros and cons of each...
-
Looking at putting a floater in and was wondering if a centered or the offset would be best,i was thinking 60in on width. whats everyone opinon,THANKS
-
-
I see some builders add a 3 inch tall bucket to the rear top spring pads and run the 16 inch springs and some builders don't add it and run the 13 inch springs, Is there a specific reason for doing...
-
Looking at recommendations for sbc oil pump,going in a stock block motor in the past ive run the melling 10550?
Whats everyones opinon?
-
Looking for the best option for a intake on a 2 barrel motor rule? Here is a few specs: 400 cubic inch,dart heads 200 runner roller motor,i have a few to choose from witch are the super victor,victor...
-
Thanks guys for all the input,problem has been found after several years of building my own stuff it was a first,i always check clearances and use plastigauge also ring gaps are always checked and...
-
Thanks guys for all the comments I have checked and rechecked every single thing suggested motor is coming back out and looks like im going in DEEP i'll post what I find in a few days,thanks again
-
Thanks Guys, smoke is bluish color and a raw oil smell,heads are new and seals do look good after double checking,intake matches good and seals(I even changed gaskets yesterday to be safe),heads are...
-
I 've spent all winter building a engine got it all done primed ready to go,after getting it in the car and letting it build up temp to seat rings it starts smoking,so I shut it off and try again the...
-
Thanks let-r-eat would you know what pressure's to start with?
-
Got a nearly new set of the base valve shocks in on a trade deal and trying to find out what kinda gas pressures to set them at and what adj to make and when,cant seem to find any info on the...
-
Has anyone run this manifold on dirt? Any feed back compared to the victor series intakes??
-
Newbie have you done anything on heads? Im thinking no one is running the mullins head or its all top secret,i haven't found anyone that has run them. :-/
-
I was wondering if anyone was running the head also and had any comments as well.
-
Only reason I ask is because I just don't know, heres what I got I picked up a callies mangun crank from a friend that changed directions in his build witch if I seen right is a little lighter than...
-
Thanks guys for the replys and positive comments I will be giving them a try soon, :-}
-
Has anyone had any experience (good or bad) With the howards promax crank and rods,possibly going in a 400 base motor on 2 barrel dirt car,thanks in advance
-
Looking for a place to have some steel heads cnc'd, whats the pro's and con's of this process?
-
I recently bought a 406 2 barrel motor that come with the sportsman heads on it but also come with a extra set of the dart platinum 215 would it be worth the gaskets to change,running in a 3200...
-
Im trying to figure out what plug I need for these heads I know its a tapered .704 reach and I need one with the shorty tip, anyone have any numbers for these,there on a 2 barrel motor on gas,Thanks...
-
IM wondering when people say they are tighting there race car what are they doing.Had a guy tell me he made his car to tight by adding stagger,Is this right or wrong? My thought to tighten for slick...
-
All times are GMT -5. The time now is 01:41 AM.
|
|