Search:

Type: Posts; User: 44xForever

Search: Search took 0.20 seconds.

  1. Replies
    0
    Views
    2,353

    2006 Bullet Chassis info

    Does anyone have set up information for an 06 Bullet chassis mod? Looking for front end geometry, settings, ball joints, etc. Have had no luck finding any information at all. Thanks in advance
  2. Can you use this with a drop or bent outer...

    Can you use this with a drop or bent outer instead of a straight outer rod?
  3. Good to know. Thanks for that too.....this car...

    Good to know. Thanks for that too.....this car was ran in IMCA in Maquoketa, it had the stud set up, but I was fairly certain that wasn't legal most places. I will look for the extreme clearance set...
  4. Would you happen to know if you can use the 5/8...

    Would you happen to know if you can use the 5/8 stud mounts and heims on the center link for the inner tie rods instead of regular inner tie rods?
  5. TS3g Thank you for the info! much appreciated. I...

    TS3g Thank you for the info! much appreciated. I will have to check the spindle on the right front, the original ball joint that was in it had a .300 spacer under the spindle the ball joint went...
  6. Chevelle stub 3 pc spindle ball joint question

    Does anyone know what ball joint is needed for stock chevelle lower control arms with allstar 55970 and 55971 3pc pinto spindles? they say they use stock metric ball joints but I don't have metric...
  7. Replies
    9
    Views
    12,330

    That is on the docket.....I am changing...

    That is on the docket.....I am changing everything on the front end so there is going to be alot of checking and measuring to do
  8. Replies
    3
    Views
    2,826

    Thank you for the info guys! appreciate it

    Thank you for the info guys! appreciate it
  9. Replies
    9
    Views
    12,330

    Unfortunately there is no way to contact the...

    Unfortunately there is no way to contact the company as they are out of business. However I am switching it to 3pc pinto/Mustang II spindles from stock pinto spindles so It shouldn't change the...
  10. Replies
    3
    Views
    2,826

    IMCA Modified Ball Joints

    Can anyone clarify the IMCA ball joint rules for Modifieds? It states OEM/OEM rebuildable ball joints approved but no screw in type lowers.......Does this mean Adjustable ball joints are not allowed?...
  11. Replies
    1
    Views
    1,099

    IMCA Modified Ball Joints

    Can anyone clarify the IMCA ball joint rules for Modifieds? It states OEM/OEM rebuildable ball joints approved but no screw in type lowers.......Does this mean Adjustable ball joints are not allowed?...
  12. Replies
    9
    Views
    12,330

    i have never ran IMCA before so i'm trying to...

    i have never ran IMCA before so i'm trying to learn their rules and regulations alittle better
  13. Replies
    9
    Views
    12,330

    Thanks for the info guys. I know both tracks are...

    Thanks for the info guys. I know both tracks are IMCA sanctioned but the rulebook was somewhat ambiguous. TS3g, are the speedway pinto 3 piece set ups are approved also?
  14. Replies
    9
    Views
    12,330

    3 piece spindles legal??

    does anyone know if 3 piece spindles are legal to run at Davenport Speedway and The Bullring in IMCA Modified division?
  15. Replies
    0
    Views
    943

    Bullet Modified Headers

    anyone know specific part numbers for longtube headers for an 2006 Bullet modified with a SBC? Not too many places list their chassis. Looking for long tube, 1 3/4 to 1 7/8 stepped or 1 7/8 tube with...
Results 1 to 15 of 15

All times are GMT -5. The time now is 11:18 AM.


Powered by vBulletin® Version 4.2.0
Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.