Search:

Well sent head to a REAL ENGINE BUILDER. Come to find out the head was bone stock and only thing done was decked. that might of cost 40 dollars so in turn i spend 1460 on a bone stock head. O maybe...

haha that head on the shelf is stock with nothing done to it.

HAHA i can see the sarcasm in that one

Dont worry buddy I got my ducks in a row.

There you go right there is the proof that you told use what to do and ruined it. We did what you told us to do.

Is your head solid or hyd? and we did as he told us to do with setting everything up. nothing was messed up except for a valve was burnt. that has nothing to do with wore out bearings so bad that...

Does anyone reading this feel i got ripped off?? We just did what he told us to do since he did so called do the head. This all started by just trying to lap the valve in and then just pulled it...

Does anyone reading this feel i got ripped off?? We just did what he told us to do since he did so called do the head.

man i talked to said he is only one that worked on it. unless he did it then you changed the parts?

HAHA haven't misspelled a word yet, but you keep acting like a child about the situation.

HAHA you told us to flat bar the cam. and then go 4* advance. Crower told us to flat bar it also. YEH PEOPLE BEWARE READ HIS POST AND LOOK HOW HE REPEATED CHANGES HIS STORY OVER AND OVER AGAIN. THATS...

HAHA and calling me uneducated

You said it was boat anchor the other night. you dont sound to educated to me. We dont run pump gas moron.

But you said it is race ready. was it race ready, NO. You told us 1500 covered everything. It was a used head. how did we rush you? you were more worried about getting the money then we were the...

Crower we called them and they said it is already advanced 4* and we called you and told you that and you said no you need to go 4* more. Your not very intelligent. Nobody said the cam, the cam...

The grooves are in the bearings not the cam. The cam is fine. So what your saying is they are used and not new? How did the valves hit the pistons?? tell me that. WTF you talking about. why would i...

the factory told us it was advanced 4* already and you insisted that we go another 4*. 4+4= 8 duh Wrapping on it? only went to like 3500 and thought u told us we needed to turn it 8500 rpm. WTF do...

O also for 1500 it didnt even come with a cam seal. he told us we had to buy one

We have told you numerous times we were on race gas. the pics you have show red paint on the inside of the head. who paints the inside of the head?? or is it rust?? we only changed timing like you...

You just admitted to telling us the wrong (not a nice word)(not a nice word)(not a nice word)(not a nice word) and it ruined the head. We run race fuel vp 110 race fuel and we told u that we ran...

I spoke to the guy who built the head, Dan didn't build nothing. The cam is only 250.00 and it is wore out also. Again Tuning has nothing to do with cam bearings being wore out with grooves. You keep...

We were happy at first cause we thought we were going to have a nice good head like you falsely said it was. Also its not hard to use a feeler gauge when at first you said set exh, and int at 10 10...

We were happy at first cause we thought we were going to have a nice good head like you falsely said it was. Also its not hard to use a feeler gauge when at first you said set exh, and int at 10 10...

Isnt 110 octane enough. mix gas was with old head and no compression 9.9:1 compression

We purchased what we thought was a new head that had a used cam in it. We were told that the cam would be degreed in and ready to bolt on the motor and go. (That was not the case at all). He told us...