|
|
Search:
Type: Posts; User: Double W Racin'
Search:
Search took 0.82 seconds.
-
Do a search on this site. Forum. Use Mustang, set up, springs, etc....
_______________________________________________________________
I just did one. I used "Mustang Setup" & "Mustang...
-
Do a search on here. There is a lot of info covering your exact question.
-
Do you remember where your static is? After Roll? and the height?:confused:
-
I've been doing A LOT of research on Mustang Front end suspension.
So far, what I've gathered, is that Asphault guys run a Sway bar and Dirt guys don't. However, I did run across a couple who...
-
I am looking to change the Roll Center on this beast. In order to do that, without modifying the chassis, I need taller Ball Joints.
Anybody have any suggestions? Or better yet... Model...
-
I was thinking of moving the roll center on the front first. Does anybody have a number for a taller upper ball joint?
-
I'd look at your cross first. You conld try a stiffer RF Spring. We are running a 650 in the Rf on our's. We also have a the large swaybar out of a Mustang II V8.
Hope that helps.
-
WOW!!!! Great suggestions. Keem 'em coming.
I'm making my list... :D
-
I have to get off my A$$ and take all of the measurements. Is there a program (free is nice) that I can just plug in the measurements into that'll help?:o
-
Race Engineering
Esslinger
Racer Walsh
Speedway Motors
There is 4 for you off the top of my head.
-
Home Sweet Home.... http://http://www.meridianspeedwayonline.com/id28.html
Ok, folks. Lets see what ya got to make this one helluva car... :D
-
Ok, I have decided to build the Mustang. It is a mid 80's trunk model. V6 chassis.
How would you build it? Tips, tricks? All mounting points must be in the stock location EXCEPT the RF upper...
-
Is welding the spider gears not an option?
-
To stop the car from rolling over on the RF so much. We have increased the RF rate and it is helping with the rollover but is also killing the tire. Was hoping that raising the rollcenter, it'd...
-
C'mon, I know you're out there.
Will it help?
-
WELL, is Mustang or Pinto?????[/QUOTE]
I'm leaning heavily toward building the Mustang. Now... Hatch or Trunk? Opinions?:rolleyes:
-
I actually did get a couple of opinions out of it all. :rolleyes:
-
If I put a couple of shims under the upper control arm mounting points, would this raise the rollcenter due to decreasing the angle of the controll arm?
Steve Smith's Pony Stock book says to raise...
-
Although I am leaning that way (pretty hard)... I still have a bit more research to do in order to completely make up my mind. :confused:
-
We've been racing Ford 2.3 rear wheel drive off and on for the past 13 years. I've built up a fairly good assortment of stuff. Not sure I wanna scrap all of that stuff and start anew. Just call me a...
-
What exactly is a "Fastboys Setup"? will in work on asphault?
-
I was thinking about removing EVERYTHING down about 3/4". Starting the turtle at that point.
-
I already have the Pinto.
Long story short... It was formerly owned and wrecked several times. It is wicked loose. I've tried to tighten it up but it crosses over to pushing like a dump truck...
-
If you had the choice... Which one would you run and why?
-
Something else to think of... You NEVER hear about the thousands of flights made every day but let one incident happen...
Those reality shows have to dig pretty deep to find footage of a wreck...
All times are GMT -5. The time now is 01:41 AM.
|
|